Dell PowerEdge R840 EMC Installation and Service Manual - Page 33
Slot Disablement, Table 5. Slot Disablement
View all Dell PowerEdge R840 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 33 highlights
Option Integrated Network Card 1 Description Enables or disables the integrated network card (NDC). When set to Disabled, the NDC is not available to the operating system (OS). This option is set to Enabled by default. NOTE: If set to Disabled (OS), the Integrated NICs might still be available for shared network access by iDRAC. I/OAT DMA Engine Enables or disables the I/O Acceleration Technology (I/OAT) option. I/OAT is a set of DMA features designed to accelerate network traffic and lower CPU utilization. Enable only if the hardware and software support the feature. I/O Snoop HoldOff Enables you to select the number of cycles PCI I/O can withhold snoop requests from the CPU to allow time to Response complete its own write to LLC. This setting can help improve performance on workloads where throughput and latency are critical. Embedded Video Controller Enables or disables the use of Embedded Video Controller as the primary display. When set to Enabled, the Embedded Video Controller will be the primary display even if add-in graphic cards are installed. When set to Disabled, an add-in graphics card will be used as the primary display. BIOS will output displays to both the primary add-in video and the embedded video during POST and pre-boot environment. The embedded video will then be disabled right before the operating system boots. This option is set to Enabled by default. NOTE: When there are multiple add-in graphic cards installed in the system, the first card discovered during PCI enumeration is selected as the primary video. You might have to re-arrange the cards in the slots in order to control which card is the primary video. Current State of Embedded Video Controller Displays the current state of the embedded video controller. The Current State of Embedded Video Controller option is a read-only field. If the Embedded Video Controller is the only display capability in the system (that is, no add-in graphics card is installed), then the Embedded Video Controller is automatically used as the primary display even if the Embedded Video Controller setting is set to Disabled. SR-IOV Global Enable Enables or disables the BIOS configuration of Single Root I/O Virtualization (SR-IOV) devices. This option is set to Disabled by default. OS Watchdog Timer If your system stops responding, this watchdog timer aids in the recovery of your operating system. When this option is set to Enabled, the operating system initializes the timer. When this option is set to Disabled (the default), the timer does not have any effect on the system. Empty Slot Unhide Enables or disables the root ports of all the empty slots that are accessible to the BIOS and OS. This option is set to Disabled by default. Memory Mapped Enables or disables the support for the PCIe devices that need large amounts of memory. Enable this option only I/O above 4 GB for 64-bit operating systems. This option is set to Enabled by default. Memory Mapped When set to 12 TB, the system will map MMIO base to 12 TB. Enable this option for an OS that requires 44 bit I/O Base PCIe addressing. Slot Disablement About this task The Slot Disablement screen details are explained as follows: Slot Disablement Enables or disables the available PCIe slots on your system. The slot disablement feature controls the configuration of the PCIe cards installed in the specified slot. Slots must be disabled only when the installed peripheral card prevents booting into the operating system or causes delays in system startup. If the slot is disabled, both the Option ROM and UEFI drivers are disabled. Only slots that are present on the system will be available for control. Table 5. Slot Disablement Slot number Description Slot 1 Enables or disables or only the boot driver is disabled for the PCIe slot 1. This option is set to Enabled by default. Slot 2 Enables or disables or only the boot driver is disabled for the PCIe slot 2. This option is set to Enabled by default. Pre-operating system management applications 33