Dell PowerEdge T30 Owners Manual - Page 74

system and aid in proper cooling and airflow inside the system.

Get Dell PowerEdge T30 PDF manuals and user guides View all Dell PowerEdge T30 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 74 highlights

NOTE: For instructions, see the documentation accompanying the card. Steps 1. Push out the expansion card release latch to open it. 2. If installed, remove the expansion-card filler. The steps for installing or removing an expansion-card filler are similar to installing or removing an expansion card. NOTE: You must install an expansion card filler bracket over an empty expansion slot to maintain Federal Communications Commission (FCC) certification of the system. The brackets also keep dust and dirt out of the system and aid in proper cooling and airflow inside the system. 3. Holding the expansion card by its edges, position the card so that the card-edge connector aligns with the expansion card connector. 4. Push the expansion card into the expansion card slot until the expansion card is fully seated. 5. Push the expansion card latch toward the system until it clicks into place. Figure 39. Removing the expansion-card filler Figure 40. Installing an expansion card Next steps 1. If applicable, connect the cables to the expansion card. 2. Follow the procedure listed in the After working inside your system section. Related tasks Before working inside your system After working inside your system 74 Installing and removing system components

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
NOTE:
For instructions, see the documentation accompanying the card.
Steps
1.
Push out the expansion card release latch to open it.
2.
If installed, remove the expansion-card filler.
The steps for installing or removing an expansion-card filler are similar to installing or removing an expansion card.
NOTE:
You must install an expansion card filler bracket over an empty expansion slot to maintain Federal
Communications Commission (FCC) certification of the system. The brackets also keep dust and dirt out of the
system and aid in proper cooling and airflow inside the system.
3.
Holding the expansion card by its edges, position the card so that the card-edge connector aligns with the expansion card connector.
4.
Push the expansion card into the expansion card slot until the expansion card is fully seated.
5.
Push the expansion card latch toward the system until it clicks into place.
Figure 39. Removing the expansion-card filler
Figure 40. Installing an expansion card
Next steps
1.
If applicable, connect the cables to the expansion card.
2.
Follow the procedure listed in the After working inside your system section.
Related tasks
Before working inside your system
After working inside your system
74
Installing and removing system components