Epson 1640XL User Manual - Page 17

If the scanner is the only SCSI device, or if it's the last device in a SCSI chain - error

Get Epson 1640XL - Expression Graphic Arts PDF manuals and user guides
UPC - 010343833548
View all Epson 1640XL manuals
Add to My Manuals
Save this manual to your list of manuals

Page 17 highlights

Follow these steps to connect the scanner to a SCSI interface: 1. Make sure the scanner and computer are turned off. (The scanner is off when the P OPERATE button is out and the ERROR and READY lights are off.) Do not connect the scanner to the computer while either is turned on, or the scanner could be damaged. 2. Squeeze the lock releases on the lock connector end of the SCSI cable, and then plug the cable into either SCSI connector on the back of the scanner. The cable is secure when both connector locks snap in. 3. Connect the pin end of the SCSI cable to the SCSI port on the computer, or to another SCSI device in the chain. Tighten the screws to secure the cable. Don't use an external terminator. 4. Locate the SCSI terminator switch at the rear of the scanner. If the scanner is the only SCSI device, or if it's the last device in a SCSI chain, leave the terminator switch turned ON. If you've connected the scanner in the middle of a SCSI chain, turn the terminator switch OFF. Terminator switch 5. Plug in the power cables for the computer, scanner, and other external SCSI devices. Using a SCSI Connection 11

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
Using a SCSI Connection
11
Follow these steps to connect the scanner to a SCSI interface:
1.
Make sure the scanner and computer are turned off. (The scanner is off when the
P
OPERATE
button is out and the
ERROR
and
READY
lights are off.)
2.
Squeeze the lock releases on the lock
connector end of the SCSI cable, and
then plug the cable into either SCSI
connector on the back of the scanner.
The cable is secure when both
connector locks snap in.
3.
Connect the pin end of the SCSI cable to the SCSI port on the computer, or to
another SCSI device in the chain. Tighten the screws to secure the cable.
4.
Locate the SCSI terminator switch at the rear of the scanner.
If the scanner is the only SCSI device, or if it’s the last device in a SCSI chain,
leave the terminator switch turned
ON
.
If you’ve connected the scanner in the
middle of a SCSI chain, turn the
terminator switch
OFF
.
5.
Plug in the power cables for the computer,
scanner, and other external SCSI devices.
Do not connect the scanner to the computer while either is turned on,
or the scanner could be damaged.
Don’t use an external terminator.
Terminator switch