Epson LX-300II Reference Guide - Page 66

Pause, Tear Off Font, button for three seconds to enter - adjustment program

Get Epson LX-300II - LX-300+ II Impact Printer PDF manuals and user guides View all Epson LX-300II manuals
Add to My Manuals
Save this manual to your list of manuals

Page 66 highlights

Follow these steps to use the control panel to select a built-in font: 1. Make sure the printer is on but not printing. If it is, wait until it stops. 2. Hold down the Pause button for three seconds to enter Micro Adjust mode. The Pause light begins to flash and the two Tear Off (Font) lights show the current font selection. 3. Press the Tear Off (Font) button repeatedly to cycle through the fonts, and stop when the lights on the control panel indicate the font you want. Your selection stays in effect until you change it again. Note: Settings you make in your application programs usually override settings you make from the printer's control panel. For best results, use your application to select a font. Bar code fonts cannot be selected from the control panel. 66 Using the Control Panel

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
66
Using the Control Panel
Follow these steps to use the control panel to select a built-in
font:
1.
Make sure the printer is on but not printing. If it is, wait until
it stops.
2.
Hold down the
Pause
button for three seconds to enter
Micro Adjust mode. The Pause light begins to flash and the
two Tear Off (Font) lights show the current font selection.
3.
Press the
Tear Off (Font)
button repeatedly to cycle through
the fonts, and stop when the lights on the control panel
indicate the font you want. Your selection stays in effect
until you change it again.
Note:
Settings you make in your application programs usually override
settings you make from the printer’s control panel. For best results, use
your application to select a font.
Bar code fonts cannot be selected from the control panel.