Epson LX-300II Reference Guide - Page 72

Using Default Setting mode, Buzzer beeper, Auto CR carriage return, IBM character table - paper out error

Get Epson LX-300II - LX-300+ II Impact Printer PDF manuals and user guides View all Epson LX-300II manuals
Add to My Manuals
Save this manual to your list of manuals

Page 72 highlights

Buzzer (beeper) The printer beeps when an error occurs. (See "Using the error indicators" on page 77 for more information on printer errors.) If you do not want the printer to beep when an error occurs, turn this setting off. Auto CR (carriage return) This setting is available only in IBM 2380 Plus emulation mode. When Auto CR is on, each line feed (LF) code or ESC J code is accompanied by a carriage return code. This moves the print position to the beginning of the next line. IBM character table This setting is available only in IBM 2380 Plus emulation mode. When you select Table 1, hex codes 80H to 90H of the character tables are used for the control codes. When you select Table 2, hex codes 80H to 90H are used for characters. Using Default Setting mode Follow the steps below to enter Default Setting mode and change the printer's default settings. Note: ❏ To print the language selection instructions and Default Setting mode instructions, you need five sheets of A4 or letter-size paper or five pages of continuous paper that is at least 11 inches (279 mm) long and 8.27 inches (210 mm) wide. ❏ If you use single sheets without an optional cut-sheet feeder, you need to insert a new sheet of paper each time the printer ejects a printed sheet. 1. Make sure paper is loaded and the printer is off. 72 Using the Control Panel

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
72
Using the Control Panel
Buzzer (beeper)
The printer beeps when an error occurs. (See “Using the error
indicators” on page 77 for more information on printer errors.) If
you do not want the printer to beep when an error occurs, turn
this setting off.
Auto CR (carriage return)
This setting is available only in IBM 2380 Plus emulation mode.
When Auto CR is on, each line feed (LF) code or ESC J code is
accompanied by a carriage return code. This moves the print
position to the beginning of the next line.
IBM character table
This setting is available only in IBM 2380 Plus emulation mode.
When you select Table 1, hex codes 80H to 90H of the character
tables are used for the control codes. When you select Table 2,
hex codes 80H to 90H are used for characters.
Using Default Setting mode
Follow the steps below to enter Default Setting mode and
change the printer’s default settings.
Note:
❏
To print the language selection instructions and Default Setting
mode instructions, you need five sheets of A4 or letter-size paper or
five pages of continuous paper that is at least 11 inches (279 mm)
long and 8.27 inches (210 mm) wide.
❏
If you use single sheets without an optional cut-sheet feeder, you
need to insert a new sheet of paper each time the printer ejects a
printed sheet.
1.
Make sure paper is loaded and the printer is off.