HP GbE2c HP GbE2c Ethernet Blade Switch for c-Class BladeSystem Browser-based - Page 171

Default Gateway Configuration

Get HP GbE2c - Blc Layer 2/3 Fiber SFP Option PDF manuals and user guides
UPC - 808736802215
View all HP GbE2c manuals
Add to My Manuals
Save this manual to your list of manuals

Page 171 highlights

Default Gateway Configuration To display the following form, go to the Default Gateways Configuration form. Select a Default Gateway ID, or open the Default Gateways folder and click Add Default Gateway. Default Gateways are disabled by default. The following table describes the Default Gateway Configuration controls: Table 140 Default Gateway Configuration controls Control Default Gateway Identifier (1-4) Default Gateway IP Address Enable/Disable Default Gateway Enable/Disable ARP only health checks Health Check Interval (0-60 sec) Retries before Out of Service (1-120) Description Selects a default Gateway to configure. Configures the IP address of the default IP gateway using dotted decimal notation. Enables or disables the gateway for use. Enables or disables Address Resolution Protocol (ARP) health checks. This command is disabled by default. The switch pings the default gateway to verify that it's up. The interval option sets the time between health checks. The range is from 0 to 60 seconds. The default is 2 seconds. Sets the number of failed health check attempts required before declaring this default gateway inoperative. The range is from 1 to 120 attempts. The default is 8 attempts. Configuring the switch 171

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
  • 207
  • 208
  • 209
Configuring the switch 171
Default Gateway Configuration
To display the following form, go to the Default Gateways Configuration form. Select a Default Gateway ID, or
open the Default Gateways folder and click
Add Default Gateway
.
Default Gateways are disabled by default.
The following table describes the Default Gateway Configuration controls:
Table 140
Default Gateway Configuration controls
Control
Description
Default Gateway Identifier (1-4)
Selects a default Gateway to configure.
Default Gateway IP Address
Configures the IP address of the default IP gateway using dotted decimal
notation.
Enable/Disable Default Gateway
Enables or disables the gateway for use.
Enable/Disable ARP only health checks
Enables or disables Address Resolution Protocol (ARP) health checks. This
command is disabled by default.
Health Check Interval (0-60 sec)
The switch pings the default gateway to verify that it’s up. The
interval
option
sets the time between health checks. The range is from 0 to 60 seconds. The
default is 2 seconds.
Retries before Out of Service (1-120)
Sets the number of failed health check attempts required before declaring this
default gateway inoperative. The range is from 1 to 120 attempts. The default
is 8 attempts.