HP Jetdirect 200m HP Jetdirect 200m Print Server (English) User Guide - Page 162

HP Jetdirect Configuration Table 9.6, TCP/IP Configuration Information 2 of 3

Get HP Jetdirect 200m PDF manuals and user guides View all HP Jetdirect 200m manuals
Add to My Manuals
Save this manual to your list of manuals

Page 162 highlights

Table 9.6 TCP/IP Configuration Information (2 of 3) Message Description DEFAULT GATEWAY: The IP address of the gateway used when sending packets off the local network. Only one default gateway may be configured. During initialization, a temporary value 0.0.0.0 is displayed. If not provided, the IP address of the Jetdirect print server is used. NOT SPECIFIED indicates that a default gateway is not configured. CONFIG BY: Identifies how the HP Jetdirect print server obtained its IP configuration: BOOTP: automatic configuration via a BOOTP server. BOOTP/TFTP: automatic configuration via a BOOTP server and TFTP configuration file. DHCP: automatic configuration via a DHCP server DHCP/TFTP: automatic configuration via a DHCP server and TFTP configuration file. RARP: automatic configuration via the Reverse Address Resolution Protocol. USER SPECIFIED: manual configuration via Telnet, the printer's control panel, HP Web JetAdmin, embedded web server, or other method. DEFAULT IP: the default IP address was assigned. This address may not be a valid address for your network. NOT CONFIGURED: The print server was not configured with IP parameters. Verify that TCP/IP is enabled, or check for error status. BOOTP SERVER: or DHCP SERVER: or RARP SERVER: Displayed if BOOTP, DHCP, or RARP is used for TCP/IP configuration. It specifies the IP address of the system that responds to the HP Jetdirect print server's request for automatic TCP/IP configuration over the network. NOT SPECIFIED indicates that the configuration server's IP address could not be determined or was set to zero in the response packet. BOOTP/DHCP SERVER: Displayed during initialization while the HP Jetdirect print server attempts to obtain its TCP/IP configuration from a BOOTP or DHCP server. The temporary address displayed is 0.0.0.0. TFTP SERVER: The IP address of the system where the TFTP configuration file is located. During initialization, the temporary address 0.0.0.0 is displayed. NOT SPECIFIED indicates that a TFTP server has not been not been set. ENWW HP Jetdirect Configuration Page 15

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
ENWW
HP Jetdirect Configuration Page 15
DEFAULT GATEWAY:
The IP address of the gateway used when sending packets
off the local network. Only one default gateway may be
configured. During initialization, a temporary value 0.0.0.0
is displayed. If not provided, the IP address of the Jetdirect
print server is used.
NOT SPECIFIED indicates that a default gateway is not
configured.
CONFIG BY:
Identifies how the HP Jetdirect print server obtained its
IP configuration:
BOOTP: automatic configuration via a BOOTP server.
BOOTP/TFTP: automatic configuration via a BOOTP
server and TFTP configuration file.
DHCP: automatic configuration via a DHCP server
DHCP/TFTP: automatic configuration via a DHCP server
and TFTP configuration file.
RARP: automatic configuration via the Reverse Address
Resolution Protocol.
USER SPECIFIED: manual configuration via Telnet, the
printer’s control panel, HP
Web JetAdmin, embedded web
server, or other method.
DEFAULT IP: the default IP address was assigned. This
address may not be a valid address for your network.
NOT CONFIGURED: The print server was not configured
with IP parameters. Verify that TCP/IP is enabled, or check
for error status.
BOOTP SERVER:
or
DHCP SERVER:
or
RARP SERVER:
Displayed if BOOTP, DHCP, or RARP is used for TCP/IP
configuration. It specifies the IP address of the system that
responds to the HP Jetdirect print server's request for
automatic TCP/IP configuration over the network.
NOT SPECIFIED indicates that the configuration server's
IP address could not be determined or was set to zero in
the response packet.
BOOTP/DHCP
SERVER:
Displayed during initialization while the HP Jetdirect print
server attempts to obtain its TCP/IP configuration from a
BOOTP or DHCP server. The temporary address
displayed is 0.0.0.0.
TFTP SERVER:
The IP address of the system where the TFTP
configuration file is located. During initialization, the
temporary address 0.0.0.0 is displayed.
NOT SPECIFIED indicates that a TFTP server has not
been not been set.
Table 9.6
TCP/IP Configuration Information (2 of 3)
Message
Description