HP Jetdirect 200m HP Jetdirect 200m Print Server (English) User Guide - Page 173

Table 9.12, Error Messages 2 of 10, LAN ERROR - WIRE

Get HP Jetdirect 200m PDF manuals and user guides View all HP Jetdirect 200m manuals
Add to My Manuals
Save this manual to your list of manuals

Page 173 highlights

Table 9.12 Error Messages (2 of 10) Error Code and Message Description 0E LAN ERROR LOSS OF CARRIER Check the network connections. If the connections are intact, run the power-on self-test: turn the printer off, then on again. If the error persists, replace the HP Jetdirect print server. 10 LAN ERROR UNDERFLOW (Ethernet) There may be a problem with your network cabling or the HP Jetdirect print server. Check the cabling and connectors on your network. If you cannot find a problem with your network cabling, run the power-on self-test: turn the printer off, then on again. If the error persists, there is a problem with the HP Jetdirect print server. 10 LAN ERROR-OPEN (Token Ring) The HP Jetdirect print server could not insert into the ring and join the network. Check the data rate switch on the HP Jetdirect print server to make sure it is set correctly. For information on setting the data rate switch, see the HP Jetdirect internal print server hardware installation guides. In addition, check the cabling, external transceiver, wiring concentrator, and taps. 11 LAN ERROR RETRY FAULTS There is a problem with your network cabling or external network configuration. Verify operation of the hub or switch port. 12 LAN ERROR NO LINKBEAT With a 10/100 Base-TX port connected, this message is displayed if Link Beat is not sensed. Check the network cable, and verify that the concentrator/hub is providing Link Beat. 13 NETWORK RECONFIG - MUST REBOOT Reset or power cycle the HP Jetdirect print server to enable new configuration values. 14 DISCONNECTED The Novell NetWare protocol is disconnected. Check the server and the print server. 15 CONFIGURATION ERROR (Ethernet) The configuration information for the NetWare functions is not stored correctly on the HP Jetdirect print server. Use the installation software, embedded web server, or other tools to reconfigure the print server. If this error persists, there may be a problem with the HP Jetdirect print server. 15 LAN ERROR - WIRE FAULT (Token Ring) The HP Jetdirect print server has detected an open or short circuit in the cable between the HP Jetdirect print server and the Token Ring wiring concentrator. Verify that this cable is functional and replace it if necessary. 26 HP Jetdirect Configuration Page ENWW

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
26 HP Jetdirect Configuration Page
ENWW
0E LAN ERROR -
LOSS OF CARRIER
Check the network connections. If the connections are
intact, run the power-on self-test: turn the printer off, then
on again. If the error persists, replace the HP Jetdirect
print server.
10 LAN ERROR -
UNDERFLOW
(Ethernet) There may be a problem with your network
cabling or the HP Jetdirect print server. Check the cabling
and connectors on your network. If you cannot find a
problem with your network cabling, run the power-on
self-test: turn the printer off, then on again. If the error
persists, there is a problem with the HP Jetdirect print
server.
10 LAN ERROR-OPEN
(Token Ring) The HP Jetdirect print server could not insert
into the ring and join the network. Check the data rate switch
on the HP Jetdirect print server to make sure it is set
correctly.
For information on setting the data rate switch, see the
HP Jetdirect internal print server hardware installation
guides. In addition, check the cabling, external transceiver,
wiring concentrator, and taps.
11 LAN ERROR -
RETRY FAULTS
There is a problem with your network cabling or external
network configuration. Verify operation of the hub or switch
port.
12 LAN ERROR -
NO LINKBEAT
With a 10/100 Base-TX port connected, this message is
displayed if Link Beat is not sensed. Check the network
cable, and verify that the concentrator/hub is providing Link
Beat.
13 NETWORK
RECONFIG - MUST
REBOOT
Reset or power cycle the HP Jetdirect print server to enable
new configuration values.
14 DISCONNECTED
The Novell NetWare protocol is disconnected. Check the
server and the print server.
15 CONFIGURATION
ERROR
(Ethernet) The configuration information for the NetWare
functions is not stored correctly on the HP Jetdirect print
server. Use the installation software, embedded web server,
or other tools to reconfigure the print server. If this error
persists, there may be a problem with the HP Jetdirect print
server.
15 LAN ERROR - WIRE
FAULT
(Token Ring) The HP Jetdirect print server has detected an
open or short circuit in the cable between the HP Jetdirect
print server and the Token Ring wiring concentrator. Verify
that this cable is functional and replace it if necessary.
Table 9.12
Error Messages (2 of 10)
Error Code and
Message
Description