HP ProLiant DL185 HP Insight Server Migration Software for ProLiant User Guide - Page 76

Use CHKDSK to detect and fix errors on all source disks prior to, migration, migration. By default

Get HP ProLiant DL185 - G5 Server PDF manuals and user guides View all HP ProLiant DL185 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 76 highlights

• 30 seconds • 60 seconds If the source-to-destination or application-station-to-destination connection cannot be established, the Next button is disabled. Ensure that ports 51125 and 51126 are open between source and destination servers. If the source-to-destination or application-station-to-destination connection is established but the network test reports a transfer speed below 250 kbps, the Next button is disabled. If the source-to-destination or application-station-to-destination connection is established and the network test reports a transfer speed of at least 250 kbps, the Next button is enabled. CAUTION: If the application-station-to-destination latency is less than 125 milliseconds, continue with the migration. Latency exceeding 125 milliseconds during driver installation might cause the driver installation to fail. Before continuing with the migration, verify the proper duplex setting, and then check the latency again. 9. Click Next. 10. Select the post-migration tasks, and then click Next. • Select whether the SMP application must perform disk-error checks on the source server before migration. By default, the Use CHKDSK to detect and fix errors on all source disks prior to migration checkbox is selected. • A reboot or shutdown option is not available for the destination virtual machine for X2V migrations when the option to manually create and the boot the destination virtual machine is selected in step 3 of the Migration Wizard. After the migration is completed, manually reboot the destination virtual machine. 76 Using SMP for server migration

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
•
30 seconds
•
60 seconds
If the source-to-destination or application-station-to-destination connection cannot be established, the
Next
button is disabled. Ensure that ports 51125 and 51126 are open between source and destination
servers.
If the source-to-destination or application-station-to-destination connection is established but the network
test reports a transfer speed below 250 kbps, the
Next
button is disabled.
If the source-to-destination or application-station-to-destination connection is established and the network
test reports a transfer speed of at least 250 kbps, the
Next
button is enabled.
CAUTION:
If the application-station-to-destination latency is less than 125 milliseconds, continue with
the migration. Latency exceeding 125 milliseconds during driver installation might cause the driver
installation to fail. Before continuing with the migration, verify the proper duplex setting, and then check
the latency again.
9.
Click
Next
.
10. Select the post-migration tasks, and then click
Next
.
•
Select whether the SMP application must perform disk-error checks on the source server before
migration. By default, the
Use CHKDSK to detect and fix errors on all source disks prior to
migration
checkbox is selected.
•
A reboot or shutdown option is not available for the destination virtual machine for X2V migrations
when the option to manually create and the boot the destination virtual machine is selected in
step 3 of the Migration Wizard. After the migration is completed, manually reboot the destination
virtual machine.
76
Using SMP for server migration