IBM 8872 Service Guide - Page 129

cover, bezel

Get IBM 8872 - eServer xSeries 460 PDF manuals and user guides
UPC - 000435813060
View all IBM 8872 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 129 highlights

4. Slide the server into the rack. 5. Connect the cables and power cords (see "Completing the installation" in the Installation Guide or User's Guide for cabling instructions). 6. Turn on all attached devices and the server. Top cover and bezel Attention: Operating the server for more than 2 minutes with the top cover removed might damage server components. For proper cooling and airflow, replace the top cover before turning on the server. To remove the top cover and bezel, complete the following steps: 1. Read the safety information that begins on page vii and "Installation guidelines" on page 99. 2. If you are installing or replacing a non-hot-swap component, turn off the server and all peripheral devices, and disconnect the power cords and all external cables. 3. Slide the server out of the rack until the slide rails lock into place. Top cover Bezel Cover release latch 4. Lift the cover-release latch. The cover slides to the rear approximately 13 mm (0.5 inch). Lift the cover off the server. 5. Press on the bezel retention tabs at the top edge of the bezel, and pull the top of the bezel slightly away from the server. 6. Lift the bezel up to release the tabs at the bottom edge of the bezel. 7. If you are instructed to return the cover and bezel, follow all packaging instructions, and use any packaging materials for shipping that are supplied to you. To install the top cover and bezel, complete the following steps: 1. Make sure that all internal cables are correctly routed. 2. Set the cover on top of the server so that approximately 13 mm (0.5 inch) extends from the rear. 3. Make sure that the cover-release latch is up. 4. Slide the top cover forward and into position, pressing the release latch closed. 5. Slide the server into the rack. Chapter 4. Removing and replacing server components 113

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
4.
Slide
the
server
into
the
rack.
5.
Connect
the
cables
and
power
cords
(see
“Completing
the
installation”
in
the
Installation
Guide
or
User’s
Guide
for
cabling
instructions).
6.
Turn
on
all
attached
devices
and
the
server.
Top
cover
and
bezel
Attention:
Operating
the
server
for
more
than
2
minutes
with
the
top
cover
removed
might
damage
server
components.
For
proper
cooling
and
airflow,
replace
the
top
cover
before
turning
on
the
server.
To
remove
the
top
cover
and
bezel,
complete
the
following
steps:
1.
Read
the
safety
information
that
begins
on
page
vii
and
“Installation
guidelines”
on
page
99.
2.
If
you
are
installing
or
replacing
a
non-hot-swap
component,
turn
off
the
server
and
all
peripheral
devices,
and
disconnect
the
power
cords
and
all
external
cables.
3.
Slide
the
server
out
of
the
rack
until
the
slide
rails
lock
into
place.
Bezel
Top cover
Cover release
latch
4.
Lift
the
cover-release
latch.
The
cover
slides
to
the
rear
approximately
13
mm
(0.5
inch).
Lift
the
cover
off
the
server.
5.
Press
on
the
bezel
retention
tabs
at
the
top
edge
of
the
bezel,
and
pull
the
top
of
the
bezel
slightly
away
from
the
server.
6.
Lift
the
bezel
up
to
release
the
tabs
at
the
bottom
edge
of
the
bezel.
7.
If
you
are
instructed
to
return
the
cover
and
bezel,
follow
all
packaging
instructions,
and
use
any
packaging
materials
for
shipping
that
are
supplied
to
you.
To
install
the
top
cover
and
bezel,
complete
the
following
steps:
1.
Make
sure
that
all
internal
cables
are
correctly
routed.
2.
Set
the
cover
on
top
of
the
server
so
that
approximately
13
mm
(0.5
inch)
extends
from
the
rear.
3.
Make
sure
that
the
cover-release
latch
is
up.
4.
Slide
the
top
cover
forward
and
into
position,
pressing
the
release
latch
closed.
5.
Slide
the
server
into
the
rack.
Chapter
4.
Removing
and
replacing
server
components
113