Home » Icom Manuals » Two-Way Radios » Icom IC-R8600 » Manual Viewer

Icom IC-R8600 Instruction Manual - Page 35

AFC function, Receiving in the CW mode, Setting the CW pitch control, About the CW Reverse mode

Add to My Manuals
Save this manual to your list of manuals

Page 35 highlights

5 OTHER FUNCTIONS AFC function Receiving FSK (RTTY) signal FM, WFM and DIGITAL modes The AFC (Automatic Frequency Control) function tunes the receive frequency into the incoming signal. LThis function activates regardless of the squelch condition. LIn the WFM mode, the receive frequency may not tune to the center frequency. 1. Push . 2. Touch [AFC]. ••Each touch turns the AFC function ON or OFF. 3. To close the MENU screen, push . Receiving in the CW mode DDSetting the CW pitch control You can set the received CW audio pitch and the CW side tone without changing the operating frequency. 1. Push . 2. Touch [CW PITCH]. 3. Rotate to adjust the pitch. ••Settable range: 300 ~ 900 Hz DDAbout the CW Reverse mode The CW-R (CW Reverse) mode reverses the receive Beat Frequency Oscillator (BFO). Use when interfering signals are near the desired signal and you want to reduce interference. CW mode (LSB side) CW-R mode (USB side) BFO Interference Desired signal BFO Interference Desired signal DDDecoded FSK data display The IC-R8600 decodes FSK signals with a built-in decoder. The decoded characters are displayed on the FSK DECODE screen. zzOpen the FSK DECODE screen in the FSK mode. MENU » DECODE Tuning indicator Decoding baud rate FFT scope When tuned into an FSK signal, the decoded characters are displayed here. DDDecoding FSK signal 1. Set the Mark frequency and Shift width on the FUNCTION screen. (p. 5-7) 2. Rotate to adjust the waveform on the FFT scope screen. LLInformatio ••Aim for a symmetrical wave form, and be sure the peak points align with the mark and shift frequency lines on the FFT scope screen. ••The S-meter displays the received signal strength, when a signal is received. ••If you cannot decode correctly, try the FSK-R (Reverse) mode. ••Tune to where both "◄" and "►" are displayed in the tuning indicator. ••The Mark and Shift frequency differ, depending on the frequency band. FSK Normal mode 1615 Hz 170 Hz FSK-R mode 170 Hz 1615 Hz BFO Mark Space Space Mark BFO Displayed frequency Displayed frequency LOn the amateur radio band, set the Mark frequency to 2125 Hz and the shift frequency to 170 Hz in the FSK-R mode. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 TIP: Reversing the carrier point The carrier point of the CW mode is LSB by default. You can change it to USB in the "CW Normal Side" item of the OTHERS set screen. (p. 11-3) MENU » SET > Function > CW Normal Side 5-5

Section	Page
PREFACE	2
IMPORTANT	2
TRADEMARKS	2
EXPLICIT DEFINITIONS	2
FEATURES	3
ABOUT THE SDR WIDEBAND RECEIVER CIRCUITS	3
VOICE CODING TECHNOLOGY	3
SUPPLIED ACCESSORIES	3
FCC INFORMATION	4
ABOUT THE INSTRUCTIONS	5
About the touch operation	5
Touch screen precautions	5
Touch screen maintenance	5
TABLE OF CONTENTS	6
PRECAUTIONS	9
1. PANEL DESCRIPTION	10
Front panel	10
Rear panel	12
Touch panel display	13
MULTI DIAL MENU ([DIAL A])	15
MULTI DIAL MENU ([DIAL B])	15
MULTI DIAL MENU ([DIAL C])	15
MENU screen	15
QUICK MENU	15
FUNCTION screen	16
FUNCTION items	16
Keyboard entering and editing	16
Entering and editing characters	16
Keyboard types	17
Entry example	17
2. INSTALLATION AND CONNECTIONS	18
Selecting a location	18
Heat dissipation	18
For desktop use	18
Grounding	18
Connecting a DC power supply	18
Power supply	18
Turning the receiver's power ON or OFF	18
Connecting an antenna	19
FSK (RTTY) connections	19
External device connection	20
3. BASIC OPERATION	21
Adjusting the volume level	21
RF gain/SQL level/Audio tone	21
Noise squelch	21
S-meter squelch	21
RF gain	21
Monitor function	21
About the VFO and Memory modes	21
Selecting the receiving mode	21
Setting the frequency	22
Directly entering a frequency	22
Changing the Tuning Step	22
About the Tuning Step (TS) function	22
About the Programmable Tuning Step function	23
About the Auto Tuning Step function	23
Selecting the antenna	23
Dial/Panel Lock function	23
Dial Lock function	23
Panel Lock function	23
Adjusting Backlight dimmer	24
Fine tuning	24
When receiving FM, WFM or DIGITAL signal	24
When receiving FSK signal	24
Selecting meter display	24
Meter display types	24
4. SCOPE OPERATION	25
Spectrum scope screen	25
RX Marker	25
Using the Spectrum Scope	25
Setting the span	26
Setting the range	26
Searching for the peak signal	27
Touch screen operation	27
Mini scope screen	27
Adjusting the Reference level	28
Sweep speed	28
Scope set screen	29
5. OTHER FUNCTIONS	31
About the Function screen	31
Preamplifier	31
Attenuator	31
Selecting the antenna	31
AGC function control	31
IP Plus function	32
Notch Filter	32
Setting the notching width and frequency	32
Using the Digital Twin PBT	32
Selecting the digital IF filter	33
Adjusting the passband width	33
Selecting the filter shape	33
Noise Blanker (NB)	34
Noise Reduction	34
Duplex operation	34
AFC function	35
Receiving in the CW mode	35
Setting the CW pitch control	35
About the CW Reverse mode	35
Receiving FSK (RTTY) signal	35
Decoded FSK data display	35
Decoding FSK signal	35
Turning ON the FSK log	36
Viewing the FSK log contents	37
Twin Peak Filter	37
FSK tone and shift setting	37
About the FSK DECODE SET screen	38
Tone squelch function	39
D.SQL (Digital Squelch) function	39
Digital Code Squelch	39
Network Access Code (NAC)	39
Group Code (COM ID) and CC	40
Radio Access Number (RAN)	40
User Code (UC)	40
Descrambler function	40
Decryption function	40
Receive history log	41
Screen Capture function	41
Capturing a screen	41
Viewing the captured screen	41
6. RECORDING AND PLAYING BACK	42
Recording	42
Quick recording	42
Normal recording	42
Playing back	42
Operation while playing back	43
Playing back on a PC	43
Checking the file information	44
Deleting a file	44
Deleting a folder	45
PLAYER SET screen	45
RECORDER SET screen	45
7. USING AN SD CARD	46
About the SD card	46
SD card’s folder contents	46
Saving data onto the SD card	46
Inserting or removing the SD card	46
Inserting	46
Removing (While the receiver is OFF)	46
Removing (While the receiver is ON)	46
Formatting an SD card	47
Saving in the old format	47
Saving the setting data	47
Loading the data files	48
Deleting a data file	48
Checking SD card information	48
8. MEMORY OPERATION	49
Memory channels	49
Selecting channel group	49
Selecting with [▲GRP]/ [▼GRP]	49
Selecting on the GROUP SELECT screen	49
Selecting a memory channel	50
Selecting with [DIAL C]	50
Selecting with [MAIN DIAL]	50
Selecting using the keypad	50
Writing a memory channel	50
Copying the Memory contents	51
Inserting a blank channel	51
Clearing a memory channel	51
Entering a group/memory name	52
Entering a group name	52
Entering a memory name	52
About the MEMORY screen	53
9. SCANS	54
Scan types	54
Basic scanning	54
VFO scan and Memory scan	54
Priority scan	54
Adjusting the scan speed	54
Setting the Scan Resume function	55
Setting the scan pause timer	55
Setting the resume delay timer	55
Setting the Scan Resume condition	55
Setting the priority interval	55
Priority scan	55
Priority scan operation	55
Monitoring the Priority channel	55
Scan Setting screen	56
Programmed scan and Fine Programmed scan	57
Programmed scan operation	57
Fine Programmed scan operation	57
∂F scan	58
∂F scan operation	58
Fine ∂F scan operation	58
Auto Memory Write scan	59
Auto Memory Write scan operation	59
Memory scan and Select Memory scan	60
Memory scan operation	60
Select Memory scan operation	60
Setting Select Memory channels	61
Canceling the Select Memory channel settings	61
Mode select memory scan	62
Setting the receive mode	62
Setting the skip frequency	62
Setting the skip frequency	62
Canceling the skip frequency	62
Setting the Temporary Skip	63
Skip channel for memory scan	63
Voice Squelch Control function	64
Tone scan operation	64
10. CLOCK AND TIMER	65
Setting the Time and Date	65
Setting date	65
Setting time	65
NTP Time Server	65
Execute the time synchronization	65
Setting the NTP Server address	65
Timer	66
Setting the Sleep timer	66
Setting the Daily timer	66
Timer setting items	67
About the Timer recording	67
11. SET MODE	68
Set mode description	68
Entering the Set mode	68
Tone Control	69
Function	69
Digital Set	71
Connectors	72
Network	74
Display	76
Time Set	77
SD Card	77
Others	77
12. MAINTENANCE	78
Cleaning	78
Replacing fuse	78
DC power cable fuses	78
Circuitry fuse	78
Resetting	79
Partial reset	79
All reset	79
Touch screen calibration	80
Troubleshooting	81
13. UPDATING THE FIRMWARE	83
General	83
About updating the firmware	83
Checking the firmware version	83
Preparation	83
Downloading the firmware file	83
Unzipping the firmware folder	83
Updating the firmware	84
14. SPECIFICATIONS	85
General	85
Receiver	85
15. OPTIONS	87
Options	87
Attaching the MB-123	87
16. CONNECTOR INFORMATION	88
ABOUT THE LICENSES	90

Match case Limit results 1 per page

OTHER FUNCTIONS

5-5

AFC function

FM, WFM and DIGITAL modes

The AFC (Automatic Frequency Control) function

tunes the receive frequency into the incoming signal.

This function activates regardless of the squelch condition.

In the WFM mode, the receive frequency may not tune to

the center frequency.

1. Push

2. Touch [AFC].

•

Each touch turns the AFC function ON or OFF.

To close the MENU screen, push

Receiving in the CW mode

Setting the CW pitch control

You can set the received CW audio pitch and the CW

side tone without changing the operating frequency.

1. Push

2. Touch [CW PITCH].

3. Rotate

to adjust the pitch.

•

Settable range: 300 ~ 900 Hz

About the CW Reverse mode

The CW-R (CW Reverse) mode reverses the receive

Beat Frequency Oscillator (BFO).

Use when interfering signals are near the desired

signal and you want to reduce interference.

CW mode (LSB side)

CW-R mode (USB side)

BFO

Interference

Desired

signal

Interference

Desired

signal

TIP: Reversing the carrier point

The carrier point of the CW mode is LSB by default.

You can change it to USB in the “CW Normal Side” item of

the OTHERS set screen. (p. 11-3)

SET > Function >

CW Normal Side

Receiving FSK (RTTY) signal

BFO

170 Hz

1615 Hz

170 Hz

1615 Hz

FSK Normal mode

FSK-R mode

Space

Mark

Space

Mark

Decoded FSK data display

The IC-R8600 decodes FSK signals with a built-in

decoder.

The decoded characters are displayed on the

FSK DECODE screen.

Open the FSK DECODE screen in the FSK mode.

DECODE

Decoding FSK signal

Set the Mark frequency and Shift width on the

FUNCTION screen. (p. 5-7)

2. Rotate

to adjust the waveform on the

FFT scope screen.

Information

•

Aim for a symmetrical wave form, and be sure the peak

points align with the mark and shift frequency lines on

the FFT scope screen.

•

The S-meter displays the received signal strength, when

a signal is received.

•

If you cannot decode correctly, try the FSK-R (Reverse) mode.

•

Tune to where both “◄” and “►” are displayed in the

tuning indicator.

•

The Mark and Shift frequency differ, depending on the

frequency band.

FFT scope

Tuning indicator

When tuned into an FSK signal, the decoded

characters are displayed here.

Decoding baud rate

On the amateur radio band, set the Mark frequency to

2125 Hz and the shift frequency to 170 Hz in the FSK-R

mode.

Displayed

frequency

Displayed

frequency