Icom IC-R8600 Instruction Manual - Page 73

SET MODE 11 Connectors (Continued) USB (Rear) > AF SQL (Default: OFF (OPEN)) Selects whether or not to output the audio from [USB] on the rear panel, according to the squelch and signal levels. ••OFF(OPEN): T he squelch is always opened regardless of the squelch and signal levels. ••ON: T he squelch opens and closes, according to the squelch and signal levels. USB (Rear) > AF Beep/Speech... Output (Default: OFF) Sets the Beep and Speech audio output status of [USB] on the rear panel. ••OFF: The beep and speech audio are not output from [USB] on the rear panel. ••ON: The beep and speech audio are output from [USB] on the rear panel. USB (Rear) > IF Output Level (Default: 50%) Sets the IF (12 kHz) output level of [USB] on the rear panel. ••Range: 0 ~ 100% USB (Rear) > Serial Function (Default: FSK Decode) Selects the signal output from [USB] on the rear panel. ••FSK Decode: An FSK decoded signal is output. ••D-STAR Data: A D-STAR data is output. USB (Rear) > FSK Decode Baud Rate (Default: 9600) Selects the data transfer rate (Baud rate) of decoded FSK signals from [USB] on the rear panel. ••Options: 4800, 9600, 19200 or 38400 (bps) USB (Rear) > D-STAR Data Baud Rate (Default: 9600) Selects the data transfer rate (Baud rate) of decoded D-STAR data from [USB] on the rear panel. ••Options: 4 800 and 9600 (bps) LAN > Output Select (Default: AF) Selects the signal output from [LAN]. ••AF: The demodulated AF signal is output. ••IF: A 12 kHz IF signal is output. LYou can listen to the Digital Radio Mondiale (DRM) broadcast with an application software receiver that is installed into your PC. LAN > AF SQL (Default: OFF (OPEN)) Selects whether or not to output the audio from [LAN], according to the squelch and signal levels. ••OFF(OPEN): T he squelch is always opened regardless of the squelch and signal levels. ••ON: T he squelch opens and closes, according to the squelch and signal levels. LAN > AF Speech Output 1 (Default: OFF) Sets the Speech audio output status of [LAN]. ••OFF: The speech audio is not output from [LAN]. ••ON: The speech audio is output from [LAN]. 2 LYou should set the "AF SQL" item to "AF." 3 CI-V > CI-V Baud Rate Selects the CI-V data transfer rate. 4 (Default: Auto) ••Options: 4800, 9600, 19200 (bps) or Auto LWhen "Auto" is selected, the baud rate is automatically set, 5 according to the data rate of the connected controller. 6 CI-V > CI-V Address Selects the CI-V address. 7 (Default: 96h) ••Range: 02h ~ 96h ~ DFh L"96h" is the default address of the IC-R8600. 8 CI-V > CI-V Transceive 9 (Default: ON) Turns the Transceive function ON or OFF. ••OFF: The status is not output. 10 ••ON: The status is output. 11 CI-V > USB/LAN→REMOTE Transceive Address  (Default: 00h) 12 Sets the address used to remotely control the receiver using the optional RS-R8600, through the [USB] or 13 [LAN] port. The external equipment control signal is output from 14 the [REMOTE] port. ••Range: 00h ~ DFh 15 TIP: When multiple devices are connected. The default transceive address is "00h." To control dedicated equipment when several devices are connected, set the same CI-V address. 16 17 18 CI-V > CI-V USB (Front) Baud Rate (Default: Auto) Selects the CI-V data transfer rate for [USB] on the front panel. 19 ••Options: 4800, 9600, 19200, 38400, 57600, 115200 (bps) or Auto 20 LWhen "Auto" is selected, the baud rate is automatically set according to the data rate of the connected controller. 21 CI-V > CI-V USB (Front) Echo Back (Default: OFF) Turns the Data Echo Back function ON or OFF, when remotely controlling through the [USB] CI-V port. ••OFF: Turns OFF the function. ••ON: Turns ON the function. 11-6