Icom IC-R8600 Instruction Manual - Page 79

Resetting, Partial reset, All reset

Get Icom IC-R8600 PDF manuals and user guides View all Icom IC-R8600 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 79 highlights

MAINTENANCE 12 Resetting Occasionally, erroneous information may be displayed. This may be caused by static electricity or by other factors. If this problem occurs, turn OFF the receiver. After waiting a few seconds, turn ON the receiver. If the problem still exists, perform a Partial reset as described below. If the problem still exists after a Partial reset, perform an All reset as described to the right. NOTE: An All reset clears all data and returns all settings to their factory defaults. Save memory channel content, setting status, and so on, onto an SD card before doing an All reset. (p. 7-2) DDPartial reset A Partial reset resets operating settings to their default values (Timer setting, NTP Server Address, Lower and upper edge of the spectrum scope, Set mode items). LNetwork settings, Reference frequency, Memory channels and Opening comments are not returned to their default value. 1. Open the RESET screen. MENU » SET > Others > Reset 2. Touch "Partial reset." ••The confirmation screen is displayed. 3. Touch [Yes]. L After resetting, the IC-R8600 will automatically restart. DDAll reset All reset clears all data and returns all settings to their 1 factory defaults. 2 1. Open the RESET screen. MENU » SET > Others > Reset 3 2. Touch "All reset." 4 ••The confirmation screen is displayed. 5 6 3. Touch [NEXT]. 7 8 9 10 11 4. After carefully reading the displayed message, touch [YES] to perform the All reset. 12 L After resetting, the IC-R8600 will automatically restart. 13 14 15 16 17 TIP: When you cannot operate the screen If a touch screen operation error or an unexpected 18 operation occurs, you cannot enter the Set mode. In that case, perform the All reset as described below: 19 1. Turn OFF the receiver power. 2. While holding down and , push . ••"ALL RESET" is displayed on the opening screen. LIf "ALL RESET" is not displayed, repeat the above procedure again. 20 21 12-2

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
12
MAINTENANCE
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
12-2
Resetting
Occasionally, erroneous information may be
displayed. This may be caused by static electricity or
by other factors.
If this problem occurs, turn OFF the receiver. After
waiting a few seconds, turn ON the receiver.
If the problem still exists, perform a Partial reset as
described below.
If the problem still exists after a Partial reset, perform
an All reset as described to the right.
NOTE:
An All reset clears all data and returns all settings
to their factory defaults. Save memory channel content,
setting status, and so on, onto an SD card before doing an
All reset. (p. 7-2)
D
Partial reset
A Partial reset resets operating settings to their default
values (Timer setting, NTP Server Address, Lower and
upper edge of the spectrum scope, Set mode items).
L
Network settings, Reference frequency, Memory channels
and Opening comments are not returned to their default
value.
1.
Open the RESET screen.
MENU
»
SET > Others >
Reset
2. Touch “Partial reset.”
•
The confirmation screen is displayed.
3. Touch [Yes].
L
After resetting, the IC-R8600 will automatically
restart.
D
All reset
All reset clears all data and returns all settings to their
factory defaults.
1.
Open the RESET screen.
MENU
»
SET > Others >
Reset
2. Touch “All reset.”
•
The confirmation screen is displayed.
3. Touch [NEXT].
4.
After carefully reading the displayed message,
touch [YES] to perform the All reset.
L
After resetting, the IC-R8600 will automatically
restart.
TIP: When you cannot operate the screen
If a touch screen operation error or an unexpected
operation occurs, you cannot enter the Set mode. In
that case, perform the All reset as described below:
1.
Turn OFF the receiver power.
2. While holding down
and
, push
.
• "ALL RESET" is displayed on the opening screen.
L
If "ALL RESET" is not displayed, repeat the above
procedure again.