Home » Icom Manuals » Two-Way Radios » Icom IC-R8600 » Manual Viewer

Icom IC-R8600 Instruction Manual - Page 54

SCANS, Scan types, Basic scanning, VFO scan and Memory scan, Priority scan

Add to My Manuals
Save this manual to your list of manuals

Page 54 highlights

9 SCANS Scan types SCAN TYPE SCANNING DETAILS VFO SCAN PROGRAMMED SCAN Repeatedly scans between 2 Scan Edge frequencies of Program Scan Edge memory channels. The scan starts from the lower edge frequency. (p.9-4) FINE PROGRAMMED During a Programed scan, the scan speed decreases when the squelch opens, but the SCAN receiver keeps scanning. The scan tuning step changes to 10 Hz when the squelch opens. ∂F SCAN Repeatedly scans within the ∂F span area. The scan starts from the center frequency, then upper edge and lower edge. (p.9-5) FINE ∂F SCAN During a ∂F scan, the scan speed decreases when the squelch opens, but the receiver keeps scanning. The scan tuning step changes to 10 Hz when the squelch opens. AUTO MEMORY WRITE During a Programed scan, and when a signal is received, the frequency is automatically SCAN stored into an Auto Memory Write channel group. (p.9-6) MEMORY SCAN MEMORY SCAN Repeatedly scans memory channels, including Skip and Auto Write memory channels. You can select the group and the scan edge channel. (p.9-7) SELECT MEMORY SCAN Repeatedly scans all or one of 9 Select Memory channels. (p.9-7) MODE SELECT MEMORY Repeatedly scans the memory channels with the selected receive mode (ignoring other SCAN receive modes). (p.9-9) PRIORITY SCAN Periodically monitors a selected memory channel while receiving a signal on VFO. (p.9-2) Basic scanning Push to start or stop a scan, then touch the desired scan type. LSee the following pages for the Scan setting details. (p. 9-3) DDVFO scan and Memory scan 1. Push . ••If you started a scan of the same scan type before, hold down for a second, to start the same scan. 2. Touch the desired scan type. SCAN START screen ••The SCAN screen opens, and the scan starts. LR otating changes the scan direction: Rotate right for the up scan, rotate left for the down scan. LTo cancel the scan, push . LYou can hide the SCAN screen during a scan. Set [Display SCAN Screen (at SCAN START)] item to "OFF" on the SCAN SETTING screen. (p. 9-3) DDPriority scan Follow the procedure below to start or stop a Priority scan.. LSee page 9-2 for setting priority channel. 1. Push . ••"PRIO" is displayed. LHold down for 1 second to monitor the priority channel. 2. Push again to cancel the scan. Adjusting the scan speed Adjust the scan speed for slower or faster scans. 1. Push . ••The setting menu opens. 2. Touch [SCAN SPEED]. 3. Rotate . ••Setting range: 1 (slow) ~ 30 (fast) LYou cannot change the scan speed during a Fine Program scan or Fine ∂F scan. 9-1

Section	Page
PREFACE	2
IMPORTANT	2
TRADEMARKS	2
EXPLICIT DEFINITIONS	2
FEATURES	3
ABOUT THE SDR WIDEBAND RECEIVER CIRCUITS	3
VOICE CODING TECHNOLOGY	3
SUPPLIED ACCESSORIES	3
FCC INFORMATION	4
ABOUT THE INSTRUCTIONS	5
About the touch operation	5
Touch screen precautions	5
Touch screen maintenance	5
TABLE OF CONTENTS	6
PRECAUTIONS	9
1. PANEL DESCRIPTION	10
Front panel	10
Rear panel	12
Touch panel display	13
MULTI DIAL MENU ([DIAL A])	15
MULTI DIAL MENU ([DIAL B])	15
MULTI DIAL MENU ([DIAL C])	15
MENU screen	15
QUICK MENU	15
FUNCTION screen	16
FUNCTION items	16
Keyboard entering and editing	16
Entering and editing characters	16
Keyboard types	17
Entry example	17
2. INSTALLATION AND CONNECTIONS	18
Selecting a location	18
Heat dissipation	18
For desktop use	18
Grounding	18
Connecting a DC power supply	18
Power supply	18
Turning the receiver's power ON or OFF	18
Connecting an antenna	19
FSK (RTTY) connections	19
External device connection	20
3. BASIC OPERATION	21
Adjusting the volume level	21
RF gain/SQL level/Audio tone	21
Noise squelch	21
S-meter squelch	21
RF gain	21
Monitor function	21
About the VFO and Memory modes	21
Selecting the receiving mode	21
Setting the frequency	22
Directly entering a frequency	22
Changing the Tuning Step	22
About the Tuning Step (TS) function	22
About the Programmable Tuning Step function	23
About the Auto Tuning Step function	23
Selecting the antenna	23
Dial/Panel Lock function	23
Dial Lock function	23
Panel Lock function	23
Adjusting Backlight dimmer	24
Fine tuning	24
When receiving FM, WFM or DIGITAL signal	24
When receiving FSK signal	24
Selecting meter display	24
Meter display types	24
4. SCOPE OPERATION	25
Spectrum scope screen	25
RX Marker	25
Using the Spectrum Scope	25
Setting the span	26
Setting the range	26
Searching for the peak signal	27
Touch screen operation	27
Mini scope screen	27
Adjusting the Reference level	28
Sweep speed	28
Scope set screen	29
5. OTHER FUNCTIONS	31
About the Function screen	31
Preamplifier	31
Attenuator	31
Selecting the antenna	31
AGC function control	31
IP Plus function	32
Notch Filter	32
Setting the notching width and frequency	32
Using the Digital Twin PBT	32
Selecting the digital IF filter	33
Adjusting the passband width	33
Selecting the filter shape	33
Noise Blanker (NB)	34
Noise Reduction	34
Duplex operation	34
AFC function	35
Receiving in the CW mode	35
Setting the CW pitch control	35
About the CW Reverse mode	35
Receiving FSK (RTTY) signal	35
Decoded FSK data display	35
Decoding FSK signal	35
Turning ON the FSK log	36
Viewing the FSK log contents	37
Twin Peak Filter	37
FSK tone and shift setting	37
About the FSK DECODE SET screen	38
Tone squelch function	39
D.SQL (Digital Squelch) function	39
Digital Code Squelch	39
Network Access Code (NAC)	39
Group Code (COM ID) and CC	40
Radio Access Number (RAN)	40
User Code (UC)	40
Descrambler function	40
Decryption function	40
Receive history log	41
Screen Capture function	41
Capturing a screen	41
Viewing the captured screen	41
6. RECORDING AND PLAYING BACK	42
Recording	42
Quick recording	42
Normal recording	42
Playing back	42
Operation while playing back	43
Playing back on a PC	43
Checking the file information	44
Deleting a file	44
Deleting a folder	45
PLAYER SET screen	45
RECORDER SET screen	45
7. USING AN SD CARD	46
About the SD card	46
SD card’s folder contents	46
Saving data onto the SD card	46
Inserting or removing the SD card	46
Inserting	46
Removing (While the receiver is OFF)	46
Removing (While the receiver is ON)	46
Formatting an SD card	47
Saving in the old format	47
Saving the setting data	47
Loading the data files	48
Deleting a data file	48
Checking SD card information	48
8. MEMORY OPERATION	49
Memory channels	49
Selecting channel group	49
Selecting with [▲GRP]/ [▼GRP]	49
Selecting on the GROUP SELECT screen	49
Selecting a memory channel	50
Selecting with [DIAL C]	50
Selecting with [MAIN DIAL]	50
Selecting using the keypad	50
Writing a memory channel	50
Copying the Memory contents	51
Inserting a blank channel	51
Clearing a memory channel	51
Entering a group/memory name	52
Entering a group name	52
Entering a memory name	52
About the MEMORY screen	53
9. SCANS	54
Scan types	54
Basic scanning	54
VFO scan and Memory scan	54
Priority scan	54
Adjusting the scan speed	54
Setting the Scan Resume function	55
Setting the scan pause timer	55
Setting the resume delay timer	55
Setting the Scan Resume condition	55
Setting the priority interval	55
Priority scan	55
Priority scan operation	55
Monitoring the Priority channel	55
Scan Setting screen	56
Programmed scan and Fine Programmed scan	57
Programmed scan operation	57
Fine Programmed scan operation	57
∂F scan	58
∂F scan operation	58
Fine ∂F scan operation	58
Auto Memory Write scan	59
Auto Memory Write scan operation	59
Memory scan and Select Memory scan	60
Memory scan operation	60
Select Memory scan operation	60
Setting Select Memory channels	61
Canceling the Select Memory channel settings	61
Mode select memory scan	62
Setting the receive mode	62
Setting the skip frequency	62
Setting the skip frequency	62
Canceling the skip frequency	62
Setting the Temporary Skip	63
Skip channel for memory scan	63
Voice Squelch Control function	64
Tone scan operation	64
10. CLOCK AND TIMER	65
Setting the Time and Date	65
Setting date	65
Setting time	65
NTP Time Server	65
Execute the time synchronization	65
Setting the NTP Server address	65
Timer	66
Setting the Sleep timer	66
Setting the Daily timer	66
Timer setting items	67
About the Timer recording	67
11. SET MODE	68
Set mode description	68
Entering the Set mode	68
Tone Control	69
Function	69
Digital Set	71
Connectors	72
Network	74
Display	76
Time Set	77
SD Card	77
Others	77
12. MAINTENANCE	78
Cleaning	78
Replacing fuse	78
DC power cable fuses	78
Circuitry fuse	78
Resetting	79
Partial reset	79
All reset	79
Touch screen calibration	80
Troubleshooting	81
13. UPDATING THE FIRMWARE	83
General	83
About updating the firmware	83
Checking the firmware version	83
Preparation	83
Downloading the firmware file	83
Unzipping the firmware folder	83
Updating the firmware	84
14. SPECIFICATIONS	85
General	85
Receiver	85
15. OPTIONS	87
Options	87
Attaching the MB-123	87
16. CONNECTOR INFORMATION	88
ABOUT THE LICENSES	90

Match case Limit results 1 per page

9-1

SCANS

Scan types

Basic scanning

SCAN TYPE

SCANNING DETAILS

VFO SCAN

PROGRAMMED SCAN

Repeatedly scans between 2 Scan Edge frequencies of Program Scan Edge memory

channels. The scan starts from the lower edge frequency.

(p.9-4)

FINE PROGRAMMED

SCAN

During a Programed scan, the scan speed decreases when the squelch opens, but the

receiver keeps scanning. The scan tuning step changes to 10 Hz when the squelch opens.

∂

F SCAN

Repeatedly scans within the

∂

F span area. The scan starts from the center frequency, then

upper edge and lower edge.

(p.9-5)

FINE

∂

F SCAN

During a

∂

F scan, the scan speed decreases when the squelch opens, but the receiver

keeps scanning. The scan tuning step changes to 10 Hz when the squelch opens.

AUTO MEMORY WRITE

SCAN

During a Programed scan, and when a signal is received, the frequency is automatically

stored into an Auto Memory Write channel group.

(p.9-6)

MEMORY SCAN

Repeatedly scans memory channels, including Skip and Auto Write memory channels.

You can select the group and the scan edge channel.

(p.9-7)

SELECT MEMORY SCAN

Repeatedly scans all or one of 9 Select Memory channels.

(p.9-7)

MODE SELECT MEMORY

SCAN

Repeatedly scans the memory channels with the selected receive mode (ignoring other

receive modes).

(p.9-9)

PRIORITY SCAN

Periodically monitors a selected memory channel while receiving a signal on VFO.

(p.9-2)

Adjusting the scan speed

Adjust the scan speed for slower or faster scans.

1. Push

• The setting menu opens.

2. Touch [SCAN SPEED].

3. Rotate

• Setting range: 1 (slow) ~ 30 (fast)

You cannot change the scan speed during a Fine

Program scan or Fine

∂F scan.

Push

to start or stop a scan, then touch the

desired scan type.

See the following pages for the Scan setting details. (p. 9-3)

VFO scan and Memory scan

1. Push

• If you started a scan of the same scan type before, hold

down

for a second, to start the same scan.

Touch the desired scan type.

• The SCAN screen opens, and the scan starts.

Rotating

changes the scan direction:

Rotate right for the up scan, rotate left for the down scan.

To cancel the scan, push

You can hide the SCAN screen during a scan. Set

[Display SCAN Screen (at SCAN START)] item to

"OFF" on the SCAN SETTING screen. (p. 9-3)

SCAN START screen

Priority scan

Follow the procedure below to start or stop a Priority scan..

See page 9-2 for setting priority channel.

1. Push

• "PRIO" is displayed.

Hold down

for 1 second to monitor the priority

channel.

2. Push

again to cancel the scan.