Icom IC-V8000 Instruction Manual - Page 22

Tuning step selection

Get Icom IC-V8000 PDF manuals and user guides View all Icom IC-V8000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 22 highlights

2 SETTING A FREQUENCY Tuning step selection USING SET MODE Tuning steps are the minimum frequency change increments when you rotate the tuning dial or push [Y]/[Z] on the microphone. The following tuning steps are available. • 5 kHz • 20 kHz • 10 kHz • 25 kHz • 12.5 kHz • 15 kHz • 30 kHz • 50 kHz NOTE: For convenience, select a tuning step that matches the frequency intervals of repeaters in your area. [SET(LOCK)] Tuning dial [MW(S.MW)] 15 kHz tuning step q Push [V/MHz(SCAN)] to select VFO mode, if necessary. w Push [SET(LOCK)] to enter set mode. e Push [SET(LOCK)] or [MW(S.MW)] several times until "TS" appears as shown at left. r Rotate the tuning dial to select the desired tuning step. t Push [TONE(T-SCAN)] to exit set mode. z Push [VFO/LOCK] to select VFO mode, if VFO/LOCK necessary. x Push [SET B(D-OFF)] to enter set mode. c Push [SET B(D-OFF)] or [ENT C(T-OFF)] several times until "TS" appears. v Push [Y] or [Z] to select the desired tuning step. b Push [CLR A(MW)] to exit set mode. 11

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
11
2
SETTING A FREQUENCY
■
Tuning step selection
Tuning steps are the minimum frequency change increments
when you rotate the tuning dial or push [
Y
]/[
Z
] on the micro-
phone. The following tuning steps are available.
•
5 kHz
•
10 kHz
•
12.5 kHz
•
15 kHz
•
20 kHz
•
25 kHz
•
30 kHz
•
50 kHz
☞
NOTE:
For convenience, select a tuning step that matches
the frequency intervals of repeaters in your area.
q
Push [V/MHz(SCAN)] to se-
lect VFO mode, if neces-
sary.
w
Push [SET(LOCK)] to enter
set mode.
e
Push
[SET(LOCK)]
or
[MW(S.MW)] several times
until
“
TS
”
appears as shown
at left.
r
Rotate the tuning dial to se-
lect the desired tuning step.
t
Push [TONE(T-SCAN)] to
exit set mode.
z
Push [VFO/LOCK] to select VFO mode, if
necessary.
x
Push [
SET
B(D-OFF)] to enter set mode.
c
Push [
SET
B(D-OFF)] or [
ENT
C(T-OFF)]
several times until
“
TS
”
appears.
v
Push [
Y
] or [
Z
] to select the desired tuning
step.
b
Push [
CLR
A(MW)] to exit set mode.
VFO/LOCK
[SET(LOCK)]
15 kHz tuning step
[MW(S.MW)]
Tuning dial
USING
SET MODE