Icom IC-V8000 Instruction Manual - Page 37

Programming a memory channel via the microphone

Get Icom IC-V8000 PDF manuals and user guides View all Icom IC-V8000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 37 highlights

MEMORY OPERATION 5 D Programming a memory channel via the microphone The microphone can also be used to program memMW ory channels. z Set the desired frequency in VFO mode. ➥ Push [VFO/LOCK] to select VFO mode. ➥ Set the frequency using the keypad. ➥ Set other data (e.g. offset frequency, duplex direction, subaudible tone encoder ON/OFF and its frequency), if neces- sary. x Push [FUNC] then [CLR A(MW)] momentarily. c Select the memory channel to be programmed. ➥ Push [Y] or [Z] to select the memory channel (direct numeral input cannot be used). v Push [FUNC] then [CLR A(MW)] for 1 sec. to program. ➥ 3 beeps may sound and the VFO contents (including the subaudible tone frequency, etc.) are programmed. 5 ➥ Memory channel number increases when continuing to push [CLR A(MW)] after programming. [EXAMPLE]: Programming 145.870 MHz into memory channel 20 (blank channel) via the microphone. Push Push Push then momentarily. Push Push then ➠ 1 sec. and continue to push " " Beep " Beep " Beep " 26

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
26
5
MEMORY OPERATION
5
D
Programming a memory channel via the microphone
[EXAMPLE]:
Programming 145.870 MHz into memory channel 20 (blank channel) via the microphone.
Push
Push
Push
then
momentarily.
Push
Push
then
1 sec. and continue to push
➠
Beep
Beep
Beep
“±
“±
“±
“±
“±
The microphone can also be used to program mem-
ory channels.
z
Set the desired frequency in VFO mode.
➥
Push [VFO/LOCK] to select VFO mode.
➥
Set the frequency using the keypad.
➥
Set other data
(e.g. offset frequency, duplex direction, sub-
audible tone encoder ON/OFF and its frequency)
, if neces-
sary.
x
Push [FUNC] then [
CLR
A(MW)] momentarily.
c
Select the memory channel to be programmed.
➥
Push [
Y
] or [
Z
] to select the memory channel
(direct nu-
meral input cannot be used)
.
v
Push [FUNC] then [
CLR
A(MW)] for 1 sec. to program.
➥
3 beeps may sound and the VFO contents (including
the subaudible tone frequency, etc.) are programmed.
➥
Memory channel number increases when continuing to
push [
CLR
A(MW)] after programming.
MW