Intel SPSH4 Product Guide - Page 102

Replacing the Backup Battery, Push the battery down until it locks into the socket.

Get Intel SPSH4 - Server Platform - 0 MB RAM PDF manuals and user guides
UPC - 735858156462
View all Intel SPSH4 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 102 highlights

To replace the battery: 1. Before proceeding, record your custom BIOS settings. 2. Disconnect the AC power cords from the power source or wall outlets. 3. Turn off all peripheral devices connected to the server system. 4. Remove the rear access cover (page 66), the system board access cover (page 68), the memory board (page 69), the air baffle (page 71), and the processor board (page 73). 5. Slide the battery in the direction shown in Figure 35, allowing the battery to pop up. 6. Remove the battery from its socket. OM13287 Figure 35. Replacing the Backup Battery 7. Dispose of the battery according to local ordinance. 8. Remove the new lithium battery from its package. 9. Being careful to observe the correct polarity, lay the battery in the socket, inserting one edge of the battery under the large corner tabs. 10. Push the battery down until it locks into the socket. 11. Install the processor board, air baffle, memory board, system board access cover, and the rear access cover. 12. Run BIOS Setup to restore the configuration settings to the RTC. 13. Restore your custom BIOS settings. 102 Intel SPSH4 Server Platform Product Guide

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
102
Intel SPSH4 Server Platform Product Guide
To replace the battery:
1.
Before proceeding, record your custom BIOS settings.
2.
Disconnect the AC power cords from the power source or wall outlets.
3.
Turn off all peripheral devices connected to the server system.
4.
Remove the rear access cover (page 66), the system board access cover (page 68), the memory
board (page 69), the air baffle (page 71), and the processor board (page 73).
5.
Slide the battery in the direction shown in Figure 35, allowing the battery to pop up.
6.
Remove the battery from its socket.
OM13287
Figure 35.
Replacing the Backup Battery
7.
Dispose of the battery according to local ordinance.
8.
Remove the new lithium battery from its package.
9.
Being careful to observe the correct polarity, lay the battery in the socket, inserting one edge of
the battery under the large corner tabs.
10. Push the battery down until it locks into the socket.
11. Install the processor board, air baffle, memory board, system board access cover, and the rear
access cover.
12. Run BIOS Setup to restore the configuration settings to the RTC.
13. Restore your custom BIOS settings.