Kenwood TS-890S Operation Manual - Page 121

SCAN 10 5 Turn the Tuning control and align the "Current" frequency as the frequency point for Program Slow Scan. 6 Press any of the function keys (F2 [POINT 1] to F6 [POINT 5]) to configure the center point of the preferred frequency range to perform Program Slow Scan. • Pressing and holding the key clears the frequency point that is stored. • Pressing and holding F7 [(CLR ALL)] clears all the frequency points. 7 Press F1 [ ] to exit the Program Slow Scan screen. The display returns to the Memory Channel List screen. 8 Press [ESC] to exit the Memory Channel List screen. ● Pressing a function key (F2 [Point 1] to F6 [POINT 5]) that already contains a frequency point overwrites the frequency point with the new input. ● When configuring a frequency point, frequencies that are smaller than 10 Hz are rounded off. Configuring the Segment for Program Slow Scan The frequency switching interval during Program Scan slows down in the preconfigured segment that contains frequencies before and after the frequency point for Program Slow Scan. Configure in Menu [4-03] "Program Slow Scan Range" Setting Value 100/ 200/ 300 (default)/ 400/ 500 [Hz] • For example, when 500 [Hz] is selected, the frequency switching interval is extended to a range of ± 500 Hz from the frequency point. Memory Scan Memory Scan allows the registered memory channel to be automatically switched at a specific time interval for scanning. There are 2 types of Memory Scan modes. All-channel Scan performs scan on all the memory channels that are registered with operating data, while Group Scan performs scan on a selected group among the memory channels. Performing Memory Scan 1 Press [M/V] to switch to the memory channel mode. 2 Press F5 [SCAN] to start memory scan. • Turning the [MULTI/CH] control allows the scan channel to jump rapidly to the next or previous channels. • Pressing F5 [SCAN] again or pressing [ESC] ends Memory Scan. • The scan direction is fixed at the ascending order. ● The frequency switching interval during Memory Scan is 400 ms. However, when a CTCSS tone is received in the FM mode, the frequency switching interval is extended to 600 ms. During Memory Scan, "SCANNING" is displayed instead of the scan speed. Configuring All-channel Scan and Group Scan 1 Press [M/V] to switch to the memory channel mode. 2 Press and hold F5 [SCAN] to display the Memory Scan group screen. Scan Hold While Program Scan (VFO Scan) is performed in a mode other than FM, changing the frequency by turning the Tuning or [MULTI/ CH] control pauses the scan operation for 5 seconds. Signals can be received temporarily without stopping the scan operation. Configure in Menu [4-04] "Scan Hold" Setting Value Off (default)/ On When Scan Hold is set to "On", signals are received with Program Scan paused for 5 seconds. . 3 Press F2 [ group. ] or F3 [ ] to select a memory 4 Press F4 [ ] or turn the [MULTI/CH] control to select whether to start scanning of the memory channels belonging to a memory group. • Pressing F4 [ ] each time selects (performs scan) or deselects (does not perform scan) the checkbox. • When performing All-channel Scan, select the checkboxes for all the memory groups. • Pressing F6 [SEL.ALL] selects the checkboxes for all memory groups. • Pressing F7 [CLR.ALL] deselects the checkboxes for all memory groups. • Memory channels are classified into memory groups as follows. The classification of the memory groups and channels cannot be altered. Group 0 1 2 3 4 5 Memory Channel 00 to 09 10 to 19 20 to 29 30 to 39 40 to 49 50 to 59 Group 6 7 8 9 P E Memory Channel 60 to 69 70 to 79 80 to 99 90 to 99 P0 to P9 E0 to E9 5 Press [ESC] to end the process. 10-3