Kenwood TS-890S Operation Manual - Page 9

CONTENTS Selecting a Tone 5-29 Configuring the Tone Frequency 5-29 Tone Frequency Scan 5-29 CTCSS Operation 5-30 Selecting CTCSS 5-30 Configuring the CTCSS Frequency 5-30 CTCSS Frequency Scan 5-30 Cross Tone 5-30 Selecting Cross Tone 5-30 Configuring the TX/RX Tones 5-30 6 REJECTING INTERFERENCE Attenuator 6-1 Switching the RX Filter Band Characteristics 6-1 Switching the RX Filter (A, B, C 6-1 Configuring the Selectable Types of RX Filters 6-1 Filter Scope 6-1 Configuring the RX Filter 6-2 Selecting a Roofing Filter 6-2 Switching the IF Filter Shape 6-2 Switching the AF Filter Type 6-2 Configuring the Behavior of the HI/SHIFT and LO/WIDTH Controls (SSB/SSB-DATA Only 6-3 Changing the Cutoff Frequency 6-3 Changing the Passband Width and Shift Amount 6-4 Preset Passband Characteristics 6-5 Audio Peak Filter in the CW Mode 6-5 Turning ON/OFF Audio Peak Filter 6-5 Switching the Passband Characteristics 6-5 Shifting the Passband Width 6-5 Configuring the Peak Gain 6-6 Audio Peak Filter in the FSK Mode 6-6 Noise Blanker 6-6 Turning ON/OFF Noise Blanker 1/2 6-6 Adjusting the NB1 Level 6-6 NB2 6-7 Configuring the NB2 Effect Level (Type A)/ NB2 Pulse Sensitivity Level (Type B 6-7 Configuring the Blanking Duration (Type B Only 6-7 Configuring the NB2 Attenuation Level (Type B Only 6-7 Notch Filter 6-8 Turning ON/OFF Notch Filter 6-8 Switching the Notch Filter Bandwidth 6-8 Noise Reduction 6-8 Turning ON/OFF Noise Reduction 6-8 Configuring the NR1 Effect Level 6-9 Configuring the NR2 Correlation Time 6-9 Beat Canceler 6-9 Turning ON/OFF Beat Canceler 6-9 DSP Monitor 6-9 Assigning DSP Monitor to PF Key 6-9 Expanding the Passband Width Using DSP Monitor 6-9 7 SCOPE FUNCTIONS Bandscope 7-1 Displaying the Bandscope 7-1 Switching the Bandscope Display Type 7-1 Adjusting the Reference Level 7-2 Switching the Bandscope Attenuator 7-2 Configuring the Speed of Waterfall Drop 7-2 Waterfall Display during Tuning (Center Mode 7-2 Reduced Bandscope Display 7-2 Switching the Scope Display Mode 7-3 Switching the Display Frequency Span 7-3 Marker Shift 7-3 Shifting the Marker 7-3 Changing the Shift Position of Marker Shift 7-3 Expand 7-4 Scope Range of Each Band (Fixed Mode 7-4 Switching the Scope Range 7-4 Configuring the Scope Range 7-4 Marker Centering (Fixed Mode 7-5 Notification on Exceeding the Lower or Upper Limit (Fixed Mode) ....... 7-5 Selecting Relative or Absolute Frequency Display for the Grid (Center Mode 7-5 Displaying Tuning Assist Line (SSB Only 7-5 Configuring the Gradation of the Waterfall 7-5 Touchscreen Tuning 7-6 Turning ON/OFF Touchscreen Tuning 7-6 Correction steps for touchscreen tuning 7-6 Turning ON/OFF Step Correction 7-6 TX/RX Frequency Marker Display 7-6 Registering Frequency Marker 7-6 Deleting a Registered Frequency 7-7 Turning ON/OFF Marker Function 7-7 Displaying the Maximum Value in the Waveform 7-7 Turning ON/OFF Maximum Value Display 7-7 Configuring the Hold Type 7-7 Pausing the Waveform Display 7-7 Averaging of Spectrum Scope Waveform 7-7 Displaying the TX Signal Waveform 7-7 Audio Scope 7-8 Displaying the Audio Scope 7-8 Switching the Audio Scope Display Type 7-8 Switching the Spectrum Scope Attenuator 7-8 Switching the Display Frequency Span of the Spectrum Scope ...... 7-8 Switching the Oscilloscope Level 7-8 Switching the Sweep Time 7-8 Pausing the Audio Scope 7-8 8 TRANSMIT FUNCTIONS Configuration of the Input Path of TX Audio 8-1 Switching the Audio Source Input 8-1 VOX (Voice-Operated Transmit 8-1 Turing ON/OFF VOX Function 8-1 Selecting Audio Source Input for Data VOX 8-2 Adjusting VOX Gain 8-2 Adjusting the Anti VOX Gain Level 8-2 Adjusting VOX Delay Time 8-3 VOX Voice Delay 8-3 TX Monitor 8-3 Adjusting the TX Monitor Level 8-3 Speech Processor 8-4 Turning ON/OFF Speech Processor 8-4 Configuring the Speech Processor Input Level 8-4 Configuring the Speech Processor Output Level 8-4 Configuring the Speech Processor Effect 8-4 TX Filter 8-5 Changing the TX Filter Bandwidth 8-5 Configuring the Low Cutoff Frequency in the SSB/AM Mode ...... 8-5 Configuring the High Cutoff Frequency in the SSB/AM Mode ..... 8-5 Configuring the Low Cutoff Frequency in the SSB-DATA/AM-DATA Mode 8-5 Configuring the High Cutoff Frequency in the SSB-DATA/AM-DATA Mode 8-5 Displaying the Filter Scope during Transmission 8-5 TX Equalizer 8-5 Turning ON/OFF TX Equalizer 8-5 Selecting a Frequency Characteristic for the TX Equalizer 8-6 vii