Kenwood TS-890S Operation Manual - Page 40
Advanced Menu Items, Reset Menu Items
View all Kenwood TS-890S manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 40 highlights
3 MENU Advanced Menu Items Menu 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 Display Description Setting Value Indication Signal Type (External Meter 1) Target of external meter output 1 Automatic/ TX Power/ ALC/ Drain Voltage (Vd)/ Compression Level (COMP)/ Current (Id)/ SWR Indication Signal Type (External Meter 2) Target of external meter output 2 Automatic/ TX Power/ ALC/ Drain Voltage (Vd)/ Compression Level (COMP)/ Current (Id)/ SWR Output Level (External Meter 1) Level of external meter output 1 0 to 100 [%] (1 step) Output Level (External Meter 2) Level of external meter output 2 0 to 100 [%] (1 step) Reference Signal Source Switches the reference signal Internal/ External Reference Oscillator Calibration Adjusts the frequency of the reference oscillator -500 to +500 (1 step) TX Power Down with Transverter Enabled Powers down the transverter function Off/ On TX Hold After Antenna Tuning Holds transmission at the end of antenna tuning Off/ On Antenna Tuner during RX Antenna tuner behavior while receiving Off/ On Antenna Tuner Operation per Band Antenna tuner behavior for each band Off/ On Microphone Gain (FM Mode) FM microphone gain 0 to 100 (1 step) PKS Polarity Reverse Reversing of PSK polarity Off/ On TX Inhibit While Busy Inhibits transmission while in the BUSY state Off/ On CTCSS Unmute for Internal Speaker Mute behavior of CTCSS Mute/ Unmute PSQ Logic State SQL control signal logic Low/ Open PSQ Reverse Condition SQL output conditions Off/ Busy/ Sql/ Send/ Busy-Send/ Sql-Send PSQ/ PKS Pin Assignment (COM Connector) PSQ/PKS mode setting Off/ On Virtual Standard COM Port RTS RTS settings of virtual COM port (Standard) Flow Control/ CW Keying/ RTTY Keying/ PTT/ DATA SEND Virtual Standard COM Port DTR DTR settings of virtual COM port (Standard) Off/ CW Keying/ RTTY Keying/ PTT/ DATA SEND Virtual Enhanced COM Port - RTS settings of virtual COM port RTS (Standard) Off/ CW Keying/ RTTY Keying/ PTT/ DATA SEND Virtual Enhanced COM Port - RTS settings of virtual COM port DTR (Standard) Off/ CW Keying/ RTTY Keying/ PTT/ DATA SEND External Display External display output Off/ On Resolution (External Display) Resolution settings of external display 800 x 600/ 848 x 480 Touchscreen Calibration Touchscreen adjustment - Software License Agreement Software license of this transceiver - Important Notices concerning Ways to obtain open source resources Free Open Source used by this transceiver - About Various Software License Agreements Licenses related to software used by this transceiver - Firmware Version Firmware version used by this transceiver - Default TX Power Automatic 50 [%] 50 [%] Internal 0 On Off Off Off 50 Off Off Mute Low Sql Off Flow Control Off Off Off On 800 x 600 - - - - - Refer to 16-6 16-6 16-6 16-6 16-8 17-2 16-15 4-12 4-12 4-12 5-28 16-12 16-12 16-8 16-8 16-8 16-8 16-12 16-12 16-12 16-12 16-7 16-7 17-3 i ii ii 17-1 Reset Menu Items Display Menu Reset Menu reset Memory Channel Reset Memory channel reset VFO Reset VFO reset Standard Reset (The Clock, TX Inhibit, and Transmit Power Upper Limit will not be reset) Standard reset Full Reset Full reset Description Refer to 17-1 3-8