Pioneer AVIC-U250 Owner's Manual - Page 16

Checking part names and, functions, Inserting an SD memory card, Resetting the microprocessor, - compatibility

Get Pioneer AVIC-U250 PDF manuals and user guides View all Pioneer AVIC-U250 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 16 highlights

Chapter 02 Introduction Checking part names and functions 1 23 4 2 Gently press the card in against the spring latch until it stops, then release. The card will lock firmly into place inside the SD card slot. 1 SD card slot p An SD memory card is used only to upgrade the software of this product. p For details of software upgrades, refer to the information on our website. 2 Video output selector switch The switch is used to change the resolution of video output to the AV receiver. ! When the switch is set to the left, WQVGA video is output. ! When the switch is set to the right, WVGA video is output. 3 Reset button = For details, refer to Resetting the microprocessor on this page. 4 Power indicator Resetting the microprocessor CAUTION Please refer to the related section before clearing. The microprocessor should be reset under the following conditions: ! Prior to using this product for the first time after installation. ! If the product fails to operate properly. ! When adding/removing additional pro- ducts that connect to the navigation system. ! If your vehicle position is shown on the map with a significant positioning error. % Press the reset button on this product with a pointed object such as the tip of a pen. Inserting an SD memory card p Compatibility with all SD memory cards is not guaranteed. 1 Insert an SD memory card into the SD card slot. Reset button 16 En

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
Checking part names and
functions
3
4
2
1
1
SD card slot
p
An SD memory card is used only to up-
grade the software of this product.
p
For details of software upgrades, refer to
the information on our website.
2
Video output selector switch
The switch is used to change the resolution
of video output to the AV receiver.
!
When the switch is set to the left,
WQVGA video is output.
!
When the switch is set to the right,
WVGA video is output.
3
Reset button
=
For details, refer to
Resetting the micro-
processor
on this page.
4
Power indicator
Inserting an SD memory card
p
Compatibility with all SD memory cards is
not guaranteed.
1
Insert an SD memory card into the SD
card slot.
2
Gently press the card in against the
spring latch until it stops, then release.
The card will lock firmly into place inside the
SD card slot.
Resetting the microprocessor
CAUTION
Please refer to the related section before clearing.
The microprocessor should be reset under the
following conditions:
!
Prior to using this product for the first time
after installation.
!
If the product fails to operate properly.
!
When adding/removing additional pro-
ducts that connect to the navigation sys-
tem.
!
If your vehicle position is shown on the
map with a significant positioning error.
%
Press the reset button on this product
with a pointed object such as the tip of a
pen.
Reset button
En
16
Chapter
02
Introduction