Pioneer AVIC-U250 Owner's Manual - Page 17

On first-time startup, Before you start

Get Pioneer AVIC-U250 PDF manuals and user guides View all Pioneer AVIC-U250 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 17 highlights

Before you start Chapter 03 Before you start On first-time startup When you use the navigation system for the first time, an initial setup process starts automatically. Follow the steps below. 1 Start the engine to boot up the system. 2 Wait approximately 10 seconds, and then press the MODE button of the AV receiver. After a short pause, the navigation splash screen appears. 3 Set the video output selector switch according to your AV receiver. p If the screen remains black after pressing the MODE button of the AV receiver, set the switch to the other side. = For details, refer to Checking part names and functions on the previous page. 4 Select the language that you want to use on the screen, then touch [Done]. 5 Read the terms carefully, checking its details, and then touch [Accept] if you agree to the conditions. The configuration wizard starts. 6 Touch [Next] to continue. 7 Select the language that you want to use for voice guidance messages, then touch [Next]. p Later you can change it in "Regional" settings. = For details, refer to Customizing the regional settings on page 60. The navigation system will restart and the "End User Licence Agreement" screen is displayed. p Later you can change it in "Sound and Warnings" settings. = For details, refer to Setting the volume and the guidance voice for navigation system on page 54. 8 If needed, modify the time format and unit settings, then touch [Next]. p Later you can change it in "Regional" settings. = For details, refer to Customizing the regional settings on page 60. En 17

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
On first-time startup
When you use the navigation system for the
first time, an initial setup process starts auto-
matically. Follow the steps below.
1
Start the engine to boot up the system.
2
Wait approximately 10 seconds, and
then press the MODE button of the AV re-
ceiver.
After a short pause, the navigation splash
screen appears.
3
Set the video output selector switch ac-
cording to your AV receiver.
p
If the screen remains black after pressing
the
MODE
button of the AV receiver, set the
switch to the other side.
=
For details, refer to
Checking part names
and functions
on the previous page.
4
Select the language that you want to
use on the screen, then touch [Done].
p
Later you can change it in
“
Regional
”
set-
tings.
=
For details, refer to
Customizing the regional
settings
on page 60.
The navigation system will restart and the
“
End User Licence Agreement
”
screen is dis-
played.
5
Read the terms carefully, checking its
details, and then touch [Accept] if you
agree to the conditions.
The configuration wizard starts.
6
Touch [Next] to continue.
7
Select the language that you want to
use for voice guidance messages, then
touch [Next].
p
Later you can change it in
“
Sound and
Warnings
”
settings.
=
For details, refer to
Setting the volume and
the guidance voice for navigation system
on
page 54.
8
If needed, modify the time format and
unit settings, then touch [Next].
p
Later you can change it in
“
Regional
”
set-
tings.
=
For details, refer to
Customizing the regional
settings
on page 60.
En
17
Chapter
03
Before you start
Before you start