Ricoh Priport HQ7000 Network Guide - Page 86

Commands List, TCP/IP address, Reference

Get Ricoh Priport HQ7000 PDF manuals and user guides View all Ricoh Priport HQ7000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 86 highlights

Appendix E Enter "yes" to save the changes, and then press the {ENTER} key. If you do not want to save the changes, enter "no", and then press the {ENTER} key. If you want to make additional changes, enter "return", and then press the {ENTER} key. Note ❒ If "Cannot write NVRAM information" appears, the changes are not saved. Repeat the steps above, as necessary. ❒ The network interface module is automatically reset when the changes are saved. ❒ When the network interface module is reset, active print jobs already sent to the printer will be finished. However, jobs not already sent will be canceled. Commands List Use the "help" command to display remote maintenance use. Note ❒ Enter "help" to display a list of commands that can be used. msh> help ❒ Enter "help command_name" to display information about the syntax of that command. msh> help command_name TCP/IP address 9 Use the "ifconfig" command to configure the Ethernet interface, IEEE 802.11b interface, and the TCP/IP (IP address, subnet mask, broadcast address, default gateway address) for the printer. ❖ Reference msh> ifconfig 80

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
Appendix
80
9
E
Enter “yes” to save the changes, and then press the
{
ENTER
}
key.
If you do not want to save the changes, enter “no”, and then press the
{
EN-
TER
}
key. If you want to make additional changes, enter “return”, and then
press the
{
ENTER
}
key.
Note
❒
If “Cannot write NVRAM information” appears, the changes are not
saved. Repeat the steps above, as necessary.
❒
The network interface module is automatically reset when the changes are
saved.
❒
When the network interface module is reset, active print jobs already sent
to the printer will be finished. However, jobs not already sent will be can-
celed.
Commands List
Use the “help” command to display remote maintenance use.
Note
❒
Enter “help” to display a list of commands that can be used.
msh> help
❒
Enter “help command_name” to display information about the syntax of that
command.
msh> help
command_name
TCP/IP address
Use the “ifconfig” command to configure the Ethernet interface, IEEE 802.11b in-
terface, and the TCP/IP (IP address, subnet mask, broadcast address, default
gateway address) for the printer.
❖
Reference
msh> ifconfig