Ricoh Priport HQ7000 Network Guide - Page 98

Configuration, msh> wiconfig

Get Ricoh Priport HQ7000 PDF manuals and user guides View all Ricoh Priport HQ7000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 98 highlights

Appendix ❖ Configuration msh> wiconfig parameter Parameter mode [ap | 802.11adhoc | adhoc] ssid ID value channel frequency channel no. enc {on | off} key {key value} 9 auth {open | shared} Value to be configured You can set infrastructure mode (ap), 802.11 ad hoc mode (802.11adhoc), or ad hoc mode (adhoc). The default is 802.11 ad hoc mode. You can set SSID in infrastructure mode. The characters that can be used are ASCII 0x20-0x7e (32 bytes). SSID value is set automatically to the nearest access point if the setting has not been made. If the setting has not been made for ad hoc mode, the same value as for infrastructure mode or an "ASSID" value is automatically set. You can set the channel. You can specify from the following channels: • Metric Version : 1-13 • Inch Version : 1-11 Set the same channel for all the machines you are using. You can enable or disable the WEP function. To enable the WEP function, select [on]; to disable it, select [off]. To start the WEP function, enter the correct WEP key. 64-bit or 128-bit can be set. Only 10 hexadecimal characters can be set when using 64-bit; or 26 hexadecimal characters when using 128-bit. Also, set 0x as the prefix. To use this function, set the same WEP key for all ports that transmit to each other. You can set the authorized mode when using WEP. The specified value and the authorized mode are as follows: open: Open system authorized (default) shared: Shared key authorized 92

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
Appendix
92
9
❖
Configuration
msh> wiconfig
parameter
Parameter
Value to be configured
mode [ap | 802.11adhoc | adhoc]
You can set infrastructure mode (ap), 802.11
ad hoc mode (802.11adhoc), or ad hoc mode
(adhoc).
The default is 802.11 ad hoc mode.
ssid
ID value
You can set SSID in infrastructure mode.
The characters that can be used are ASCII
0x20-0x7e (32 bytes).
SSID value is set automatically to the nearest
access point if the setting has not been made.
If the setting has not been made for ad hoc
mode, the same value as for infrastructure
mode or an “ASSID” value is automatically set.
channel frequency
channel no.
You can set the channel.
You can specify from the following channels:
•
Metric Version : 1-13
•
Inch Version : 1-11
Set the same channel for all the machines you
are using.
enc {on | off}
You can enable or disable the WEP function.
To enable the WEP function, select [on]; to
disable it, select [off].
To start the WEP function, enter the correct
WEP key.
key {
key value
}
64-bit or 128-bit can be set.
Only 10 hexadecimal characters can be set
when using 64-bit; or 26 hexadecimal charac-
ters when using 128-bit.
Also, set 0x as the prefix.
To use this function, set the same WEP key
for all ports that transmit to each other.
auth {open | shared}
You can set the authorized mode when using
WEP. The specified value and the authorized
mode are as follows:
open: Open system authorized (default)
shared: Shared key authorized