Sharp AR-M280 AR-M280 AR-M350 AR-M450 Operation Manual (for multifunction - Page 110

System settings initialize/store settings, Restore factory defaults, Store current configuration,

Get Sharp AR-M280 PDF manuals and user guides View all Sharp AR-M280 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 110 highlights

KEY OPERATOR PROGRAMS System settings (initialize/store settings) The settings of the configuration settings (page xx) and the system settings of the key operator programs (pages xx to xx) can be reset to the factory default settings. Also the current settings can be stored to the memory and the stored settings can be recalled from the memory after the settings have been changed. In "Initialize/Store Settings", the following programs can be set. G Restore factory defaults G Store current configuration G Restore configuration *1 Restore factory defaults This program is used to reset the settings of the configuration settings (page xx) and the system settings (default settings/interface settings) of the key operator programs (pages xx to xx) to the factory default settings. If you wish to record the settings before resetting, use "List Print" of custom settings to print the settings before using this program. NOTE After this program is set, exit the key operator program, turn off the main switch, and then turn on the main switch again after a while. The program will be effective at this time. NOTE For programs marked with *1, a confirmation message for execution will appear at the end of operation procedure. When the operation panel on the main unit is used, execution of the program can be canceled by pressing the [BACK/C] key. When the operation panel with touch panel is used, execution of the program can be canceled by touching the [CANCEL] or [NO] key. System settings (product key) Use these programs to perform product key (password) input operation in the following cases. G To use this product as a PostScript compatible printer The password to be entered is described in the operation manual supplied with the optional PS3 expansion kit. G To use the network scanner feature (only if the operation panel with touch panel is used) The password to be entered is described in the operation manual supplied with the network scanner expansion kit (peripheral unit). *1 Store current configuration Use this program to store the current settings of the configuration settings (page xx) and the system settings (default settings/interface settings) of the key operator programs (pages xx to xx) in the printer's nonvolatile memory.To recall the stored settings, use the program "Restore configuration" below. *1 Restore configuration Use this program to recall the configuration settings that have been stored in the printer's nonvolatile memory using the program "Store current configuration" above. NOTE If this program is executed when the setting of "Enable TCP/IP", "Enable NetWare", "Enable EtherTalk" or "Enable NetBEUI" has been changed, exit the key operator program, turn off the main switch, and then turn on the main switch again after a while. The program will be effective at this time. 6-14

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
6-14
KEY OPERATOR PROGRAMS
System settings (initialize/store settings)
The settings of the configuration settings (page xx)
and the system settings of the key operator programs
(pages xx to xx) can be reset to the factory default
settings. Also the current settings can be stored to
the memory and the stored settings can be recalled
from the memory after the settings have been
changed.
In “Initialize/Store Settings”, the following programs
can be set.
●
Restore factory defaults
●
Store current configuration
●
Restore configuration
*
1
Restore factory defaults
This program is used to reset the settings of the
configuration settings (page xx) and the system
settings (default settings/interface settings) of the
key operator programs (pages xx to xx) to the factory
default settings. If you wish to record the settings
before resetting, use "List Print" of custom settings
to print the settings before using this program.
NOTE
After this program is set, exit the key operator program,
turn off the main switch, and then turn on the main switch
again after a while. The program will be effective at this
time.
*
1
Store current configuration
Use this program to store the current settings of the
configuration settings (page xx) and the system
settings (default settings/interface settings) of the
key operator programs (pages xx to xx) in the printer's
nonvolatile memory. To recall the stored settings, use
the program "Restore configuration" below.
*
1
Restore configuration
Use this program to recall the configuration settings
that have been stored in the printer's nonvolatile
memory using the program "Store current
configuration" above.
NOTE
If this program is executed when the setting of "Enable
TCP/IP", "Enable NetWare", "Enable EtherTalk" or "Enable
NetBEUI" has been changed, exit the key operator
program, turn off the main switch, and then turn on the
main switch again after a while. The program will be
effective at this time.
NOTE
For programs marked with *1, a confirmation message for
execution will appear at the end of operation procedure.
When the operation panel on the main unit is used,
execution of the program can be canceled by pressing
the [BACK/C] key.
When the operation panel with touch panel is used,
execution of the program can be canceled by touching
the [CANCEL] or [NO] key.
System settings (product key)
Use these programs to perform product key
(password) input operation in the following cases.
●
To use this product as a PostScript compatible
printer
The password to be entered is described in the
operation manual supplied with the optional PS3
expansion kit.
●
To use the network scanner feature (only if the
operation panel with touch panel is used)
The password to be entered is described in the
operation manual supplied with the network
scanner expansion kit (peripheral unit).