Sharp AR-MM9 Service Manual - Page 17

[6] SIMULATION 1. Code-type simulation A. Operating procedures and operations * Entering the simulation mode 1) #/P key (program) ON → Asterisk (*) key ON → CLEAR key ON → Asterisk (*) key ON → Ready for input of a main code of simulation 2) Entering a main code with the 10-key → START key ON 3) Entering a sub code with the 10-key → START key ON 4) Select an item with the scroll key and the item key. 5) The machine enters the mode corresponding to the selected item. Press START key to start the simulation operation. To cancel the current simulation mode or to change the main code and the sub code, press the CUSTOM SETTINGS key. * Canceling the simulation mode to return to the normal mode 1) Press CLEAR ALL key. 2. Simulation code list Code Main Sub 22 5 11 24 10 46 12 13 14 15 16 48 8 9 50 8 9 66 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 Function Used to check the ROM version of each unit (section). Used to display the FAX send/receive counter (FAX reception and print counter). FAX counter data clear FAX exposure level adjustment (1 mode automatic adjustment) FAX exposure level adjustment (Normal mode individual adjustment) FAX exposure level adjustment (Fine text mode individual adjustment) FAX exposure level adjustment (Super Fine mode individual adjustment) FAX exposure level adjustment (Ultra Fine mode individual adjustment) FAX magnification adjustment (read) FAX magnification adjustment (print) FAX lead edge adjustment (read) FAX lead edge adjustment (print) Used to change and check the FAX-related soft SW. Used to clear the FAX-related soft SW. (Except for the FAX adjustment values) FAX PWB memory check Signal send mode (Signal send level: Max.) Signal send mode (Signal send level soft SW setting) Printing the confidential password Print the screen memory contents Voice Message send (Signal send level: Max.) (print) (Japan only) Used to send the voice message. (Signal send level: Set by soft SW.) Image data memory clear Used to send 300bps signals. (Signal send level: Max.) Used to send 300bps signals. (Signal send level: Set by soft SW) Used to register the dial numbers. Used to perform the dial test. (10 PPS send test) Used to perform the dial test. (20 PPS send test) Used to perform the dial test. (DTFM signal send test) Code Main Sub 66 17 18 19 20 21 22 24 30 31 32 33 34 37 41 Function Used to check the DTFM signal send operation. (Signal send level: Max.) Used to check the DTFM signal send operation. (Signal send level: Set by soft SW.) Used to write the SRAM data to the Flash ROM. Used to write the Flash ROM data to the SRAM. FAX information print Handset sound volume adjustment (Japan only) Used to clear the FAST storage data. (SEC only) Used to set the TEL/LIU. Used to set the TEL/LIU. Receive data check Signal detection check Communication time measurement display Speaker sound volume adjustment CI signal check 3. Details 22 22-5 Purpose Function (Purpose) Item Adjustment/Setting/Check Used to check the ROM version of each unit (section). Software Operation/procedure Used to display the ROM version of each section. [Display example] ROM version 1.250 → [1.25] (up to 2 decimal places) The display of the protocol monitor and the soft SW follows this display. S/N MCU IMC OPE PRINTER NIC FINISHER FAX Machine serial number Main Control Unit IMC Panel + Panel label code PRINTER NIC (For the Soft Nic, the Soft Nic version is displayed. When the AR-NC5 is installed, the AR-NC5J version is displayed.) FINISHER FAX If it is not installed is displayed. [Label code display] Contents of "XXX" section on the display below Panel display JPN EFS EEU Destination Japan SEC SECL SUK SEEG/ SEA/East Europe, etc. Selection code AJ/AM AL/AC BK/BB GG/GD Panel software support language Japanese, American English, English American English, English, French, Spanish English, German, Polish, Czech, Hungarian, Greek, Turkish, Russian, French, Italian, Slovak AR-FX7 SIMULATION 6 - 1