Sharp AR-MM9 Service Manual - Page 73

2. Power switch Keep the machine's power switch turned on at all times. Faxes cannot be received if the power is turned off. ON Far edge Top edge Bottom edge 3. Originals A. Original sizes Minimum original size Maximum original size Using the RSPF 8-1/2" (width) x 5-1/2" (length) [210 mm (width) x 148 mm (length)] 5-1/2" (width) x 8-1/2" (length) [148 mm (width) x 210 mm (length)] 11" (width) x 39.3"* (length) [297 mm (width) x 1000 mm (length)] ∗ Long originals can be loaded. When the scanning resolution is Ultra fine, the maximum length is 34.6" [880 mm]. Using the document glass 11" (width) x 17" (length) [297 mm (width) x 420 mm (length)] NOTE: • Originals that are not a standard size (5-1/2" x 8-1/2", 5-1/2" x 8-1/ 2"R, 8-1/2" x 11", 8-1/2" x 11"R, 8-1/2" x 14", 11" x 17") can also be faxed. • Because the amount of memory is limited, the scannable length of a long original will vary depending on the resolution setting and the width of the original. If the memory fills up before the entire original can be scanned, use a lower resolution setting or shorten the original. • There are restrictions on originals that can be scanned using the RSPF. *Long originals Depending on the resolution setting and the width of the original, there may not be sufficient space in memory to hold a long original. In this case, refer to the following table and select a lower resolution setting and/or shorten the original. Standard Fine Super fine Ultra fine 11" wide 39.3" [1000 mm] 39.3" [1000 mm] 39.3" [1000 mm] 34.6" [880 mm] 8-1/2" wide 39.3" [1000 mm] 39.3" [1000 mm] 39.3" [1000 mm] 39.3" [1000 mm] B. Scanning area of original Note that the edges of an original cannot be scanned. Area that cannot be scanned: • 0.2" [5 mm] or less at top edge and 0.2" [5 mm] or less at bottom edge • Near edge + far edge = 0.24" [6 mm] Area that cannot Near edge be scanned C. Automatic reduction of faxed document If the width of the faxed document is greater than the receiving machine's maximum receivable width, the document will be automatically reduced. Faxed document width 11" x 17" 11" x 17" 8-1/2" x 14" Receiving machine's paper width 8-1/2" x 14" 8-1/2" x 11" 8-1/2" x 11" Reduced size 8-1/2" x 14" 8-1/2" x 11"R 8-1/2" x 11"R Ratio 1 : 0.70 (Area ratio) 1 : 0.5 (Area ratio) 1 : 0.64 (Area ratio) A document can also be faxed without reducing its size. In this case, the left and right edges will not be transmitted. 4. Own number sending This function prints the date, time, your programmed senderís name, your programmed sender's fax number, and the page number at the top center of each page that you fax. Example of fax page printed out by the receiving machine MAY-11-200X-FRI 03:00 PM ↑ 1) SHARP PLANNING DIV. ↑ 2) FAX No.0666211221 ↑ 3) P.001/001 ↑ 4) 1) Date and time: programmed in the custom settings. 2) Sender's name: programmed in the key operator programs. 3) Sender's fax number: programmed in the key operator programs. 4) Page number: 3-digit number appearing in the format, "page number/total pages" (only the page number appears if you use manual transmission or Quick On-Line transmission). If desired, you can use a key operator program to have the page number omitted. A. Position of sender's information You can select whether the sender's information is added outside the printed fax image or inside the image in the key operator programs. The initial factory setting is outside the image. Outside scanned data Direction of transmission Length of scanned data Length of transmitted data None of the transmitted image is cut off; however, the transmitted image is longer than the scanned image, and thus when both the sender and the receiver use the same size of paper, the printed fax may either be reduced or split up and printed on two pages. AR-FX7 KEY OPERATOR PROGRAM 8 - 3