Sharp AR-MM9 Service Manual - Page 65

SW67 No.1-No.4 After sending CFR, double wait is inhibited for 1.6sec. Used to set that the double wait is inhibited for 1.6sec. after sending CFR. Setup is made in the range of 0ms - 3000ms by binary input. Default: 1600ms SW67 No. 5 Measurement of communication time (image) Used to set YES/NO of measurement. Used to measure the communication time in phase C. However, it is the communication time in the latest phase C. (Unit: msec) Default: 1 (YES) SW67 No. 6 Reduction transmission mode Used to set whether the transmitted document is received in reduction size or both ends of recording paper are cut when the transmitted document width is greater than the recording paper width. When set to 1, the document is sent without reduction with the both ends cut. When set to "0", it is reduced and transmitted. Default: 0 (Reduction) SW67 No. 7 ECM Used to set whether ECM (Error Correction Mode) is performed or not. When, however, SW43-1 (V.34 mode function) is set to OFF, or when SW43-1(V.34 mode function is set to ON and the transmission is not the super G3 transmission, ECM Disable setup is effective. This is because the ECM function is indispensable in a transmission other than super G3 transmission in V.34 mode and the other party machine may perform checking. With SW43-1 (V.34 mode function) is ON and this reception function is disabled. When set to 1, ECM is enabled. When set to "0", ECM is disabled. Default: 1 (ECM is enabled) SW67 No. 8 ECM byte/frame Used to set ECM byte/frame. Default: 0 (256 [bytes/frame]) SW68 No.1-No.4 Recording paper tray selection (Tray 1 - 4) Used to select the tray for output of the received documents. Tray 1 to Tray 4 can be set to ON/OFF individually. When set to OFF, the tray does not output received documents. Setup is made by selecting bit 1 - bit 4. Each bit is selected in the sequence of tray 1 - tray 4. When 1 is selected, output is made by using that tray. When 0 is selected, output is not made by using that tray. Default: Tray 1 - tray 4 are used. (1) bit 1 : Tray 1 bit 2 : Tray 2 bit 3 : Tray 3 bit 4 : Tray 4 SW68 No.5-No.8 The tray specification of Duplex print (Tray 1 - 4) Used to select the tray for output of the duplex documents. Tray 1 to Tray 4 can be set to ON/OFF individually. When set to OFF, the tray does not output received documents. Setup is made by selecting bit 5 - bit 8. Each bit is selected in the sequence of tray 1 - tray 4. When 1 is selected, output is made by using that tray. When 0 is selected, output is not made by using that tray. Default: Tray 1 - tray 4 are used. (1) bit 5 : Tray 1 bit 6 : Tray 2 bit 7 : Tray 3 bit 8 : Tray 4 SW69 No.1, No.2 Reception size specification (Reception capacity) Used to set the receivable document width which is notified to the other party when receiving a document. The setup items are as follows: bit 1 2 0 0 : By the equipped cassette 0 1 : B4 (A4, B4) 1 0 : A4 1 1 : A3 (A4, B4, A3) Default: 0 0 (Varies depending on the installed cassette.) Max. allowed reception width selection Max. allowed reception width is determined by Table 1 and Table 2. This determines the transmitted size from the other party. When set to A3 with SW69-12, only with B5 cassette, proxy reception is always performed. Do not use this combination. (Because division process in the main scanning direction is not performed.) When set to A4 with SW69-12, , A3 document from the other party is not divided into A4 paper but reduction to A4width is requested to the other party. • Max. allowed reception width setup SW69 No.1 No.2 Size specification Allowable reception width 0 0 Depends on the installed cassette. Varies according to the table below. 0 1 B4 A4 & B4 width 1 0 A4 A4 width 1 1 A3 A4 & B4 & A3 width • Max. allowable reception width by installed cassette [Max. paper size of installed cassette with FAX function] → [Sampled paper size (data width)] A5 → A4 B5 → B4 A4 → A3 B4 → B4 A3 → A3 No cassette with FAX function → A3 SW69 No. 3 11 inch reception capacity setup When SW69-12, is set to "Depends on installed cassette," the max. allowable reception width by 8.5" × 11" cassette is set. When set to 1, the reception allowable width is 255mm or 215mm. When set to 0, the reception allowable width is 303mm or 255mm or 215mm. Default: 0 (the reception allowable width is 303mm or 255mm or 215mm) SW69 No. 4 Maximum reception length Used to set the receivable document width which is notified to the other party when a long document is sent from the other party. When set to 1, reception is made without limitations. When set to 0, if reception of a document reaches 1.5m, reception is terminated. Default: 0 (Reception is terminated after receiving 1.5m.) SW69 No.5, No.6 Image quality in transmission request Used to set the image capacity of the machine when send request (polling). Reflected on DTC. Default: 0 0 (ultra fine) SW69 No. 7 Countermeasures for echo in reception (CED tone send interval) Used to select ON/OFF of countermeasures against echo. An interval of 500ms is inserted before DIS transmission. Default: 0 (75ms) AR-FX7 SOFT SWITCH 7 - 37