Sharp AR-MM9 Service Manual - Page 55

SW Data No. No. Items 1 Inhibited to use 2 3 S4 W 133 5 6 7 8 SW selection and functions Default value 0 0 1 1 0 0 0 0 Remarks 3. Soft switch descriptions SW1 No.1-No.8 Country information Destination setup SW2 No.1, No.2 SIM language information SIM language selection SW2 No.3-No.8 Language information Language selection SW3 No. 1 Sharp machine mode Sharp machine mode setup Default: 1 (ON) SW3 No. 2 Sharp machine mode (F code) Sharp machine mode (F code) setup Default: 0 (OFF) SW3 No. 3 FAST mode (Canada: Inhibited to use) Used to set Enable/Disable of FAST operation. This SW must be set to enable FAST operation by the serviceman. Default: 0 (NO) SW3 No. 4 Center number in FAST (Canada: Inhibited to use) Center number setup in FAST Default: 0 (Service-No.) SW3 No.5-No.7 Maintenance cycle (Canada: Inhibited to use) Setup for judgment of consumable parts notification when using the F.A.S.T. function. This setup should be the same as SIM21-1 setup. Default: 0 0 1 (75K) SW3 No. 8 Maintenance system Setting of the machine model for judgment of consumable parts system in the FAST function Default: 0 (AR) SW4 No.1-4 Inhibited to use. SW4 No.5-No.8 RingBackTone pre-send times Used to set RingBackTone pre-send times. Setup is made in the range of 0 - 15 times by binary input. Default: 0 time (fixed) SW5 No. 1 Initialization control inside program Used to set whether the all soft switches are initialized or not. When set to 1, the initialization is made. When set to 0, No initialization is made. Default: 0 (nothing is made) SW5 No. 2 For FAX debug Used to set ON/OFF of FAX debug mode. When set to 1, debug mode is ON. When set to 0, debug mode is OFF. Default: 0 (Debug mode OFF) SW5 No. 3 Flash memory check measuring range Operation check usually can be done by 256-byte check. Setting to 1 will check all areas of the flash memory. Note that it takes about 20 min. Default: 0 (256 bytes) SW5 No. 4 ICU UART1 output Used to set whether ICU UART 1 output is made or not. Default: 1 (Output is not made) SW5 No.5-No.8 24V reset wait time Used to set the 24V reset wait time. The set range is 0 to 750 by binary input. Default: 500ms SW6 No. 1 Auto/Manual default setup Used to select Auto/Manual reception mode when turning on the power. (When no external telephone is connected, do not select Manual. However, setup is possible and reception can be made by onhook.) When set to 1, manual reception. When set to 0, auto reception. Default: 0 (Auto reception) SW6 No. 2 Inhibited to use. SW6 No.3, No.4 Size specification Used to set inch series or AB series for recording paper when printing received documents. Normally there is no need to change from "Follow the machine information." Default: 0 1 (follows the machine information) SW6 No. 5 Inhibited to use. SW6 No. 6 Memory transmission/direction transmission default setup Used to select Memory/Direction transmission when the power is turned on and the time out is cleared. When set to 1, direct transmission is selected when the power is turned on and the time out is cleared. When set to 0, memory transmission is selected when the power is turned on and the time out is cleared. Default: 0 (Memory transmission) SW6 No. 7 Quick memory transmission Used to set whether quick memory transmission (transmission of ringing before completion of scanning) is performed or not. Linked with the key operator program menu. Default: 1 (Allowed) AR-FX7 SOFT SWITCH 7 - 27