Sharp AR-MM9 Service Manual - Page 60

SW31 No.3-No.8 Time specification print (min) on the communication report table Used to set "min" of the time (o'clock, min) when specifying the time on the communication report table. Setup is in the range of 0 - 59 (min) by binary input. (When set to 60 - 63, the time is set to 0min.) Default: 0 min SW32 No.1, No.2 Default telephone book setup Used to set YES/NO of default telephone book displaying. Default: 0 0 (Basic screen) SW32 No. 3 Next address key input in broadcast Used to set YES/NO of Next address key input in broadcast. Default: 0 (No) SW32 No.4, No.5 One-touch dial display number switch Used to set the number of one-touch dial display. Default: 0 1 (8) SW32 No. 6 Shift of the power OFF state in shut off Used to set whether the shift of the power OFF state in shut off is allowed or inhibited. Default: 1 (allowed) SW32 No. 7 Time indication format Used to set the sequence of year, month, and day in the LCD display, report, and sender record. When set to 1, time is indicated in AM/PM format. When set to 0, time is indicated in 24H format. Default: 1 (AM/PM format) SW32 No. 8 Priority in the day of week Used to set the recording sequence of the day of month and the day of week if the date is in the sequence of month, day, and year. Default: 0 (NO) SW33 No. 1 Inhibited to use. SW33 No. 2 Report output on less than A4 (LTR) Used to set the report output on less than A4 (LTR). Default: 0 (Reduction by the record volume) SW33 No. 3 Inhibited to use. SW33 No.4, No.5 Contents of send document are printed in memory send Used to set Print/Not print part of the sent document in the transmission result table in case of a memory transmission error. When set to 0 0, the transmitted document is not printed on the transmission result table. When set to 0 1, all the transmitted document are printed on the transmission result table. When set to 1 0, the transmitted document is printed on the transmission result table only when the transmission is failed. Default: 1 0 (when the transmission is failed) SW33 No. 6 Transmission document content print in F code transmission Used to set whether the sent document content is print or not in F code transmission. SW33-4 - 5 must be set to output. Default: 1 (Not print) SW33 No. 7 Function to attach images to the report table of memory confidential send Used to set whether images are attached to the report table of memory confidential send Default: 0 (NO) SW33 No. 8 Total communication time and total number of pages print on communication record table Used to set Print/Not print the total communication time and the total number of pages on the communication record table. When set to 1, the total communication time and the total number of pages are printed on the communication record table. When set to 0, not printed on the communication record table. Default: 1 (YES) SW34 No.1, No.2 Report output (in reception) Used to set whether the communication report table is outputted or not when a reception (excluding confidential reception) is made. Setup is selected from "print inhibition," "all output," and "only when transmission is failed" as follows: bit 1 2 0 0 : Print is inhibited. 0 1 : Print all 1 0 : Only in case of an error Default: 0 0 (printing is inhibited) SW34 No.3, No.4 Report output (in transmission) Used to set whether the communication report table is outputted or not after the transmission (excluding broadcast, sequential send request, and relay broadcast). Setup is selected from "print inhibition," "all output," and "only when transmission is failed" as follows: bit 3 4 0 0 : Print is inhibited. 0 1 : Print all 1 0 : Only when transmission is failed Default: 1 0 (Only when transmission is failed) SW34 No. 5 Communication report output (in confidential reception) Used to set whether the communication report table is outputted or not when a confidential reception is made. When set to 1, the communication report table is printed. When set to 0, the communication report table is not printed. Default: 1 (Print) SW34 No.6, No.7 Report output (In broadcast, sequential send request, and relay broadcast) Used to set whether the communication report table is outputted or not after the transmission (in broadcast, sequential send request, and relay broadcast). Setup is selected from "print inhibition," "all output," and "only the address to which transmission is failed" as follows: bit 6 7 0 0 : Print is inhibited. 0 1 : Print all 1 0 : Only the address to which transmission is failed Default: 0 1 (All print) SW34 No. 8 Report output when canceling Used to set whether the communication report table is outputted or not when canceling transmission during document transmission. When set to 1, the communication report table is printed. When set to 0, the communication report table is not printed. Default: 0 (No print) SW35 No. 1 Automatic reduction print Used to set whether the received document is automatically reduced and printed so that the print-out is fit in a fixed size when the document size is longer than the fixed sizes but smaller than the max. length of automatic reduction ratio. When set to 1, the document is printed with automatic reduction. When set to 0, the document is printed without reduction. Default: 1 (Automatic reduction print enable) AR-FX7 SOFT SWITCH 7 - 32