Sharp AR-MM9 Service Manual - Page 78

2. Communication result code Described on the communication report table, the communication management table, and the protocol communication report table when communication is completed. A. Composition of communication report code Communication result X X (X X X X) Upper 2 digits of a communication result code: Communication report code of 00 - 90 (Refer to the list of communication report codes.) Lower 4 digits of a communication result code: Codes used by serviceman. Top 2 digits Bottom 2 digits Communication report sub code 1 (Refer to the list of communication sub code 1.) Communication report sub code 2 (Refer to the list of communication sub code 2.) Note) Communication report sub code 1 and sub code 2 are in hexadecimal. (The others are in decimal.) Result code Final reception signal (Transmitting side) Final reception signal (Receiving side) 0 Abnormal signal Abnormal signal 1 NSF, DIS (SID), (SUB), NSS, DCS 2 CFR (PWD), (SEP), NSC, DTC 3 FTT EOP 4 MCF EOM 5 PIP, PIN MPS 6 RTN, RTP PRI-Q 7 No signal, DCN DCN 8 PPR PPS-EOP 9 PPS-EOM 10 PPS-MPS, PPS-NULL 11 RNR RR 12 CTR CTC 13 ERR EOR-Q 14 PPS-PRI-Q 15 16 Abnormal signal Abnormal signal 17 NSF, DIS SID, SUB, NSS, DCS 18 CFR PWD, SEP, NSC, DTC 19 FTT PPS-EOP 20 MCF PPS-EOM 21 PIP, PIN PPS-MPS, PPS-NULL 22 RTN, RTP PRI-Q 23 No signal, DCN DCN 24 PPR 25 RNR RR 26 CTR CTC 27 ERR EOR-Q 28 PPS-PRI-Q 29 V.8 Phase-1 V.8 Phase-1 30 V.8 Phase-2 V.8 Phase-2 31 V.8 Phase-3 V.8 Phase-3 (Note) For result codes 16 - 31, V.34 mode communication. For 32 or later, refer to the table below. Result code (Communication result) 0 - 31 33 Communication report result column Refer to the previous table. Busy Communication interruption content Depends on the communication disconnection position. For 16 or later, V.34 mode communication. The calling side cannot connect the line with the other party. Result code (Communication result) 34 35 38 42 44 46 48 49 50 51 56 59 60 61 Communication report result column Cancel Power OFF Reception memory over Reception length over Document error No response from the other party OK The other party has no polling function. Polling is not accepted. Polling allow number discrepancy Interface not accepted The other party has no function of F code bulletin board. F code polling is not accepted. F code bulletin board number discrepancy Communication interruption content When a communication interruption command is delivered during transmission or reception, When the operation is interrupted by the stop key. When the power is cur off during sending or receiving, When memory is over during reception, . When printing cannot be performed during reception due to inhibition of proxy reception, When the received data length of one page exceeds the range during reception, When a document jam occurs during direct transmission, When the FAX signal from the other party is not detected within T1 time, Communication normal end When the called side has no polling function in polling reception, When the called side has no transmission data, When DCN is received for DTC in polling reception, When there is no transmission data in polling transmission, When the allow number does not coincide in polling transmission, When the system number does not coincide in polling transmission, 1) When DCN is received for NSS in transmission of the relay instruction, 2) When a receiving station number that is not registered is instructed in reception of the relay instruction, 3) When F code relay instruction is received during F code relay broadcasting, When the other party machine does not have DIS bit 47 (Selective polling function) in F code polling (ringing), When DCN is received for SEP in F code polling (ringing), When there is no transmission data for SEP in bulletin board, When the sub address (bulletin board number (SEP)) does not coincide in bulletin board, AR-FX7 TROUBLE CODE LIST 10 - 2