Sharp AR-MM9 Service Manual - Page 57

SW10 No. 8 Send request protection Used to set YES/NO of the confidential protection function (inhibition of transmission to an erroneous party). Confidential protection is performed by collating the number registered in this machine and that in the other party's machine. (Sender's telephone number ↔ Send request allow number, System number ↔ ID number) When set to 1, protection is not made. When set to 0, protection is made. Default: 0 (Protection) SW11 No. 1 Dept. management Used to set Enable/Disable of FAX using dept. management by the use of the dept. management function. When set to 1, the department management function is enabled. When set to 0, the department management function is not used. Default: 0 (Dept. management is disabled) SW11 No. 2 Inhibited to use. SW11 No. 3 Sender's telephone number registration Used to set whether the registered sender's TEL No. can be changed or not. When set to 1, sender's TEL No. cannot be registered and changed. To prevent sender's TEL No. from being changed erroneously, this is set to 1. Default: 0 (Enabled) SW11 No. 4 Yes/No of manual send selection menu display Used to set whether the manual transmission selection screen is displayed or not. Default: 1 (displayed) SW11 No.5-No.8 Distinctive ringing The function judges TEL or FAX by CI ringing. Default: 0 0 0 0 (OFF) SW12 No. 1 Direct send recall Allow/Inhibit Used to set Allow/Inhit of direct send recall. Default: 1 (allowed) SW12 No.2-No.7 Inhibited to use. SW12 No.8 Remote selection models Used to set remote selection models. Default: 0 (Call-in only) SW13 No.1-No.4 Recall times in busy Used to set the number of recall times in case of busy state of the other party or when call does not reach the other party. Setup is made in the range of 0 - 14 times by binary input. When set to 0, recall is not made. Default: 2 times of recall SW13 No.5-No.8 Recall interval in busy Used to set recall interval after disconnection due to the busy state of the other party or no response. The set range is 1 to 15 min in the increment of 1 min by binary input. When set to 0, it is the same as setup of 3 min. Default: 3 min SW14 No.1-No.4 Recall number in case of a transmission error Used to set the number of recall times in case of a communication error. Setup is made in the range of 0 - 1 times by binary input. When set to 0, recall is not made. Default: 1 time of recall SW14 No.5-No.8 Recall interval in communication error Used to set recall interval after disconnection of communication due to a communication error in memory transmission. The set range is 0 to 15 min in the increment of 1 min by binary input. When set to 0, recall is made immediately after disconnection. However, the time interval set by SW41-5-8 (Interval between the end of a communication and the next call) is taken. Default: 1 min SW15 No. 1 - No.3 Inhibited to use. SW15 No.4-No.8 Signal send level Used to set the attenuation quantity of signal send level from the modem. 0 (0dBm) to 26 (-26dBm) Default: -11dBm SW16 No.1-No.4 Modem speed (V.33 mode or less) Used to set the speed to start communication. When communication troubles occur frequently, the speed may be reduced to solve the troubles. Default: 1 0 0 0 (V.17 14.4kbps) SW16 No.5, No.6 Modem speed in reception fixed Used to set the start speed of reception procedure when receiving from the other party other than V.34. bit 5 6 0 0 : No fixing 0 1 : V.29-9600BPS 1 0 : V.27ter-4800BPS 1 1 : V.17-14400BPS When set to "no fixing," the operations are the same as V.1714400BPS. The above four setups are possible. The reception procedure is started at the set communication speed. Default: 0 0 (no fixing) Reception is made at the proper communication speed. SW16 No. 7 EOL detection timer Used to set the detection timer of EOL (End Of Life) when Phase-C reception. When set to 1, the timer is set to 25sec. When set to 0, the timer is set to 13sec. Default: 0 (13 sec) SW16 No. 8 RTN EOL send times Used to set the RTN EOL send times. Default: 1 (6 times) SW17 No. 1 Inhibited to use. SW17 No. 2 MH fixed (except for SG3) Used to set whether the encoding system is fixed to MH or not in a mode other than SG3 communication. When set to 1, the encoding system is fixed to MH. When set to 0, the encoding system is not fixed to MH. Default: 0 (The encoding system is not fixed to MH.) SW17 No. 3 ECM MMR mode (except for SG3) Used to set whether MMR encoding system is allowed or inhibited, except for SG3 communication. When set to 1, MMR encoding system is allowed. When set to 0, MMR encoding system is inhibited. Default: 1 (MMR encoding system is allowed) AR-FX7 SOFT SWITCH 7 - 29