Sharp AR-MM9 Service Manual - Page 29
Soft Switch
![]() |
UPC - 074000074828
View all Sharp AR-MM9 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 29 highlights
[7] SOFT SWITCH 1. FAX soft switch setting change quick reference table Large item Dialing Middle item Remote machine call disable Switch content Pause time Dial call signal DTMF-related item Key operator Default setting Default setting None None None Signal detection Redial In case of an error In case of an error When busy When busy Arrival (Call-in) When CI detection disable External telephone Setting of an external telephone connected Remote switch number Remote switch setting Communication General Pulse (10PPS) None Busy tone detection None Busy tone detection None Dial tone detection None Resend interval Transmitter function setting Number of times of resend Transmitter function setting Resend interval Transmitter function setting Number of times of resend Transmitter function setting CI detection None CI signal OFF detection time None Yes/No Default setting Entry of a 2-digit number Yes/No Send level Default setting None None SG3 JBIG mode V34 mode function setup None None V34 symbol rate None Transmission G3/SG3 DIS reception check Line equalizer One-touch/ Reduction, etc. None SG3 G3 Reception G3/SG3 SG3 G3 V34 send speed Manual send V34 One-touch/ Reduction, etc. None V29 no modulation carrier None Modem send speed RTN reception error CSI transmission Maximum reception length Proxy reception EQM dispersion inhibit One-touch/ Reduction, etc. None None None None None V34 reception speed None Countermeasure against echo in reception Modem speed in reception None None EYE-Q check only None Soft SW No. Usage SW 28-1 - 4 When dialing disable/when error dialing SW 22-5, 6 When dialing disable SW 64-4 - 8 When dialing disable in PBX (private branch exchange/Fax service, etc.) SW 65-5 - 8 When dialing disable in PBX (private branch exchange/Fax service, etc.) SW 26-1 - 5 When dialing disable in PBX (private branch exchange/Fax service, etc.) SW 25-1 - 4 When pulse dialing disable SW 21-2 When busy tone detection disable SW 51-1 - 2 When busy tone error is detected SW 21-1 SW 14-5 - 8 When send errors occur frequently SW 14-1 - 4 SW 13-5 - 8 Whey busy occurs frequently SW 13-1 - 4 SW 86-2, 3 No call-in SW 87-1 - 7 No call-in SW 41-1 When an external telephone is connected SW 7-1 - 8 When remote switch is erroneously detected SW 6-8 When remote switch is erroneously detected SW 15-4 - 8 SW 17-4, 8 SW 43-1 SW43-4 - 6 SW 69-8 When the remote machine cannot receive signals in a proper level. When an error occurs in the JBIG mode When SG3 communication error occurs frequently When SG3 communication error occurs frequently When an error occurs in phase B SW 42-8 SW 16-1 - 4 Setting is made referring to the distance from the station when a communication trouble occurs. When an error occurs in the SG3 communication. When an error occurs in the SG3 communication in FAX service, etc. When an error occurs in the V29 communication To specified/unspecified destination SW 73-1 When judged as "OK" though RTN is received When a document of 1m or longer is received When a lot of errors occur due to the poor conditions of the line. When fall-down occurs frequently in the SG3 communication When an error occurs in phase B in reception SW 16-5, 6 SW 72-7 When the line quality is poor and a fall-back or an error occurs Change in the detection method of training error AR-FX7 SOFT SWITCH 7 - 1
![](/manual_guide/products/sharp-armm9-service-manual-b289390/29.png)