Brother International HE-800A Instruction Manual - English - Page 44

Parameter table

Get Brother International HE-800A PDF manuals and user guides View all Brother International HE-800A manuals
Add to My Manuals
Save this manual to your list of manuals

Page 44 highlights

5. OPERATION ５-５. Parameter table ▪ The parameter values can be stored independently for each program. ▪ The allowable setting range for some parameters may vary from the range specified, depending on the settings of other parameters. (Refer to "5-5-4. Main restrictions when setting parameters".) • Depending on the needle zigzag amount and feed amount settings, it may not be possible to carry out sewing at some setting speeds. ▪ The zigzag width ratio cannot be set when the rear tack pattern is set to an eyelet pattern. ▪ If all underlays have been set, the order of sewing is underlays sewn together, then saw-shape underlays and then rectangle underlays. • Parameters that are not applicable to a particular program will be skipped and not displayed. No. Setting items 00 Sewing speed (zigzag part) 01 Buttonhole stitch/Straight tack stitch 0: 1: 2: 3: 4: Setting range 1,000 - 4,000rpm 0: Buttonhole (free) 1: Buttonhole (rectangle) 2: Buttonhole (radial) 3: Buttonhole (round) 4: Bar tack Unit 100 1 Default 3,600 1 02 Length of knife 04 Zigzag pitch 4.0 - 32.0mm However, when panel DIP switch B - No. 3, No. 4 and No. 5 are at OFF, OFF and ON respectively when initialization is carried out, the initial value will be set to 6.0. 0.10 - 2.00mm 0.1 0.025 13.0 （6.0） 0.350 05 Zigzag width 1.0 - 3.0mm 0.1 1.5 06 Knife X space -0.4 - 1.0mm 0.1 0.4 07 Knife Y space 0.00 - 2.00mm 0.05 1.00 HE-800A 36

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
HE-800A
5. OPERATION
36
５
-
５
. Parameter table
▪
The parameter values can be stored independently for each program.
▪
The allowable setting range for some parameters may vary from the range specified, depending on the settings of
other parameters. (Refer to “5-5-4. Main restrictions when setting parameters”.)
• Depending on the needle zigzag amount and feed amount settings, it may not be possible to carry out sewing at some
setting speeds.
▪
The zigzag width ratio cannot be set when the rear tack pattern is set to an eyelet pattern.
▪
If all underlays have been set, the order of sewing is underlays sewn together, then saw-shape underlays and then
rectangle underlays.
• Parameters that are not applicable to a particular program will be skipped and not displayed.
No.
Setting items
Setting range
Unit
Default
00
Sewing speed (zigzag part)
1,000 - 4,000rpm
100
3,600
Buttonhole stitch/Straight tack stitch
01
0:
1:
2:
3:
4:
0: Buttonhole (free)
1: Buttonhole (rectangle)
2: Buttonhole (radial)
3: Buttonhole (round)
4: Bar tack
1
1
02
Length of knife
4.0 - 32.0mm
However, when panel DIP
switch B – No. 3, No. 4 and
No. 5 are at OFF, OFF and
ON
respectively
when
initialization is carried out, the
initial value will be set to 6.0.
0.1
13.0
（
6.0
）
04
Zigzag pitch
0.10 - 2.00mm
0.025
0.350
05
Zigzag width
1.0 - 3.0mm
0.1
1.5
06
Knife X space
-0.4 - 1.0mm
0.1
0.4
07
Knife Y space
0.00 - 2.00mm
0.05
1.00