Brother International HE-800A Instruction Manual - English - Page 58

Cutter operation

Get Brother International HE-800A PDF manuals and user guides View all Brother International HE-800A manuals
Add to My Manuals
Save this manual to your list of manuals

Page 58 highlights

５-８. Cutter operation The cutter operating pattern can be selected from the following four patterns. Parameter No. 44 0 1 2 5. OPERATION 3 Operates when the front tack of the last buttonhole cycle is sewn. 3935Q Operates near the front tack when sewing is finished and material is feeding. 3936Q Operates immediately before the left zigzag stitch of the last cycle is sewn. 3937Q Operates twice: immediately before the left zigzag stitch of the last cycle is sewn and when the front tack of the last cycle is sewn. 3938Q Setting range 0: General sewing Setting range 1: Because the needle and knife positions are separated by 2.2 mm as shown in the illustration, the distance between the edge of the front tack and the edge of the buttonhole cannot be set to less than 2.2 mm. For example, if the knife Y space (A) is set to 0.5 mm, the front tack length (B) will not go below 1.7 mm. At such times, the front tack length can be set to less than 1.7 mm when using cutting after sewing. Once sewing is finished and material feeding has finished, the cutter will operate. 2.2 mm Feeding 3939Q Setting range 2: • Does not operate during the first sewing cycle. Only applies to second and subsequent cycles (during underlay sewing and overlap sewing). ▪ This is used in cases such as when the rough edges of the material after cutting are hemmed by the buttonhole stitches. ▪ The cutter operates before the left zigzag stitch of the last cycle is sewn. Setting range 3: • Does not operate during the first sewing cycle. Only applies to second and subsequent cycles (during underlay sewing and overlap sewing). ▪ This is used in cases such as when the rough edges of the material after cutting are hemmed by the buttonhole stitches. ▪ It can also be used if the rough edges of the material block the buttonhole after the left and right zigzag stitches have been sewn. • The cutter operates immediately before the left zigzag stitch of the last cycle is sewn, and it operates again when the front tack of the last cycle is sewn. HE-800A 50

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
HE-800A
5. OPERATION
50
５
-
８
. Cutter operation
The cutter operating pattern can be selected from the following four patterns.
Parameter No. 44
0
1
2
3
Operates when the front
tack of the last buttonhole
cycle is sewn.
Operates near the front
tack
when
sewing
is
finished and material is
feeding.
Operates
immediately
before the left zigzag stitch
of the last cycle is sewn.
Operates
twice:
immediately before the left
zigzag stitch of the last
cycle is sewn and when the
front tack of the last cycle is
sewn.
Setting range 0:
General sewing
Setting range 1:
Because the needle and knife positions are separated
by 2.2 mm as shown in the illustration, the distance
between the edge of the front tack and the edge of the
buttonhole cannot be set to less than 2.2 mm.
For example, if the knife Y space (A) is set to 0.5 mm,
the front tack length (B) will not go below 1.7 mm. At
such times, the front tack length can be set to less than
1.7 mm when using cutting after sewing.
Once sewing is finished and material feeding has
finished, the cutter will operate.
Setting range 2:
• Does not operate during the first sewing cycle. Only applies to second and subsequent cycles (during underlay sewing
and overlap sewing).
▪
This is used in cases such as when the rough edges of the material after cutting are hemmed by the buttonhole
stitches.
▪
The cutter operates before the left zigzag stitch of the last cycle is sewn.
Setting range 3:
• Does not operate during the first sewing cycle. Only applies to second and subsequent cycles (during underlay sewing
and overlap sewing).
▪
This is used in cases such as when the rough edges of the material after cutting are hemmed by the buttonhole
stitches.
▪
It can also be used if the rough edges of the material block the buttonhole after the left and right zigzag stitches have
been sewn.
•
The cutter operates immediately before the left zigzag stitch of the last cycle is sewn, and it operates again when the
front tack of the last cycle is sewn.
3937Q
3936Q
3938Q
3935Q
3939Q
2.2 mm
Feeding