Cisco WS-C3750X-24T-L Hardware Installation Guide - Page 146

Methods for Accessing the CLI, Accessing the CLI Through Express Setup (Uncon d Switch Only)

Get Cisco WS-C3750X-24T-L PDF manuals and user guides View all Cisco WS-C3750X-24T-L manuals
Add to My Manuals
Save this manual to your list of manuals

Page 146 highlights

Methods for Accessing the CLI Appendix D Quick Setup By Using the CLI-Based Setup Program Methods for Accessing the CLI You can access the CLI by these methods: • Accessing the CLI Through Express Setup (Unconfigured Switch Only), page D-2 • Accessing the CLI Through the Console Port, page D-3 Accessing the CLI Through Express Setup (Unconfigured Switch Only) Note Express Setup is supported on switches running Cisco IOS Release 12.1(14)EA1 or later. If you are installing a new switch, refer to the Cisco IOS release label on the rear panel of the switch to determine the release. For switches running releases earlier than Cisco IOS Release 12.1(14)EA1, go to the "Taking Out What You Need" section on page D-4. You can access the CLI on an unconfigured switch by placing the switch in Express Setup mode and then connecting an Ethernet port of the switch to the Ethernet port of your PC or workstation. To put the switch into Express Setup mode, follow the steps described in these sections of Chapter 1, "Using Express Setup": • Taking Out What You Need, page 1-2 • Powering On the Switch, page 1-3 • Starting Express Setup, page 1-4 After the switch is in Express Setup mode, Telnet to the switch by using the IP address 10.0.0.1, and enter the setup user EXEC command. See these sections in this chapter to then configure the switch by using the CLI: • Entering the Initial Configuration Information, page D-10 • Completing the Setup Program, page D-11 After you have entered the configuration information for the switch, save it to Flash memory by using the write memory privileged EXEC command. Catalyst 3750 Switch Hardware Installation Guide D-2 78-15136-02

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
Appendix D
Quick Setup By Using the CLI-Based Setup Program
Methods for Accessing the CLI
D-2
Catalyst 3750 Switch Hardware Installation Guide
78-15136-02
Methods for Accessing the CLI
You can access the CLI by these methods:
•
Accessing the CLI Through Express Setup (Unconfigured Switch Only),
page D-2
•
Accessing the CLI Through the Console Port, page D-3
Accessing the CLI Through Express Setup (Unconfigured Switch
Only)
Note
Express Setup is supported on switches running Cisco IOS Release 12.1(14)EA1
or later. If you are installing a new switch, refer to the Cisco IOS release label on
the rear panel of the switch to determine the release.
For switches running releases earlier than Cisco IOS Release 12.1(14)EA1, go to
the
“
Taking Out What You Need
”
section on page D-4
.
You can access the CLI on an unconfigured switch by placing the switch in
Express Setup mode and then connecting an Ethernet port of the switch to the
Ethernet port of your PC or workstation. To put the switch into Express Setup
mode, follow the steps described in these sections of
Chapter 1,
“
Using Express
Setup
”
:
•
Taking Out What You Need, page 1-2
•
Powering On the Switch, page 1-3
•
Starting Express Setup, page 1-4
After the switch is in Express Setup mode, Telnet to the switch by using the IP
address
10.0.0.1
,
and enter the
setup
user EXEC command. See these sections in
this chapter to then configure the switch by using the CLI:
•
Entering the Initial Configuration Information, page D-10
•
Completing the Setup Program, page D-11
After you have entered the configuration information for the switch, save it to
Flash memory by using the
write memory
privileged EXEC command.