Compaq ProLiant 6400R Compaq ProLiant 6400R Servers - Page 105

Otherwise, run the System Configuration Utility.

Get Compaq ProLiant 6400R PDF manuals and user guides View all Compaq ProLiant 6400R manuals
Add to My Manuals
Save this manual to your list of manuals

Page 105 highlights

3-38 Compaq ProLiant 6400R Maintenance and Service Guide Table 3-18 ADU Diagnostic Messages continued Message Description Identify controller data did not match with NVRAM The identify controller data from the array controller did not match the information stored in nonvolatile RAM. This could occur if new, previously configured drives have been placed in a system also previously configured. It could also occur if the firmware on the controller has been upgraded and the System Configuration Utility was not run. Identify logical drive data did not match with NVRAM The identify unit data from the array controller did not match the information stored in nonvolatile RAM. This could occur if new, previously configured drives have been placed in a system also previously configured. Insufficient adapter resources The adapter does not have sufficient resources to perform operations to the array accelerator board. Drive rebuild may be occurring. Less than 75% batteries at sufficient voltage Operation of array accelerator board has been disabled because of less than 75% of battery packs at a sufficient voltage level. Less than 75% batteries at sufficient voltage. Battery pack X below reference voltage Battery pack on array accelerator is below required voltage levels. Logical drive X failed due to cache error The logical drive failed because of a catastrophic cache error. Recommended Action Check the identify controller data under the Inspect Utility. If the firmware version field is the only difference between the controller and nonvolatile RAM data, this is not a problem. Otherwise, run the System Configuration Utility. Run the System Configuration Utility to configure the controller and nonvolatile RAM. Operate the system without the array accelerator board until the drive rebuild completes. Allow sufficient time for the batteries to recharge (36 hours). If the batteries have not recharged after 36 hours, replace the array accelerator board. Allow sufficient time for batteries to recharge (36 hours). If batteries have not recharged after 36 hours, replace the array accelerator board. Replace the array accelerator board and reconfigure it using the ACU. continued

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
3-38
Compaq ProLiant 6400R Maintenance and Service Guide
Table 3-18
ADU Diagnostic Messages
continued
Message
Description
Recommended Action
Identify
controller data
did not match
with NVRAM
The identify controller data from the
array controller did not match the
information stored in nonvolatile
RAM. This could occur if new,
previously configured drives have
been placed in a system also
previously configured. It could also
occur if the firmware on the
controller has been upgraded and the
System Configuration Utility was not
run.
Check the identify controller data under the
Inspect Utility. If the firmware version field is the
only difference between the controller and
nonvolatile RAM data, this is not a problem.
Otherwise, run the System Configuration Utility.
Identify logical
drive data did
not match with
NVRAM
The identify unit data from the array
controller did not match the
information stored in nonvolatile
RAM. This could occur if new,
previously configured drives have
been placed in a system also
previously configured.
Run the System Configuration Utility to
configure the controller and nonvolatile RAM.
Insufficient
adapter
resources
The adapter does not have sufficient
resources to perform operations to
the array accelerator board. Drive
rebuild may be occurring.
Operate the system without the array
accelerator board until the drive rebuild
completes.
Less than 75%
batteries at
sufficient voltage
Operation of array accelerator board
has been disabled because of less
than 75% of battery packs at a
sufficient voltage level.
Allow sufficient time for the batteries to
recharge (36 hours). If the batteries have not
recharged after 36 hours, replace the array
accelerator board.
Less than 75%
batteries at
sufficient
voltage. Battery
pack X below
reference
voltage
Battery pack on array accelerator is
below required voltage levels.
Allow sufficient time for batteries to recharge
(36 hours). If batteries have not recharged after
36 hours, replace the array accelerator board.
Logical drive X
failed due to
cache error
The logical drive failed because of a
catastrophic cache error.
Replace the array accelerator board and
reconfigure it using the ACU.
continued