Compaq ProLiant 6400R Compaq ProLiant 6400R Servers - Page 82

SMART-2 Controller error. Data

Get Compaq ProLiant 6400R PDF manuals and user guides View all Compaq ProLiant 6400R manuals
Add to My Manuals
Save this manual to your list of manuals

Page 82 highlights

Diagnostics and Troubleshooting 3-15 Table 3-2 POST Error Messages continued Error Code Audible Beeps 1774-Slot x Drive None Array - Obsolete data found in Array Accelerator. Select F1 to discard contents of Array Accelerator. Select F2 to write contents of Array Accelerator to drives. 1775-Slot x Drive None Array - ProLiant Storage System Not Responding SCSI Port (y): Check storage system power switch and cables. Turn the system power off while checking the ProLiant power and cable connections, then turn the system power back on to retry. 1776-Drive Array - None SCSI Port Termination Error 1777-Drive Array None External Drive Subsystem Error 1778-Drive Array None resuming Automatic Data Recovery process 1779-Drive Array None Controller detects replacement drives 1780-Disk 0 Failure None 1781-Disk 1 Failure None Probable Source of Problem SMART-2 Controller error. Data found in the array accelerator are older than data found on drives. Recommended Action Press F1 to discard the older data in the array accelerator and retain the newer data on the drives. Storage system error Turn off power to system. Check the external ProLiant power switch. External drives must all be powered up before or at the same time as the main system. Check the cables. If a retry does not help, replace the cable, ProLiant firmware, ProLiant backplane, or Smart Array Controller. External and internal SCSI drives Reconfigure drives. are both configured to port 1. Cooling fan failure, internal temperature alert, or open side panel A controller reset or power cycle occurred during automatic data recovery. Inspect for cooling fan failure or open side panel. No action necessary. Intermittent drive failure and/or possible loss of data Hard drive/format error Hard drive/format error If this message appears and drive X has not been replaced, an intermittent drive failure has occurred. This message also appears once immediately after drive replacement whenever data must be restored from the backup. Run Diagnostics. Replace the failed assembly as indicated. Run Diagnostics. Replace the failed assembly as indicated. continued

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
Diagnostics and Troubleshooting
3-15
Table 3-2
POST Error Messages
continued
Error Code
Audible Beeps
Probable Source of Problem
Recommended Action
1774-Slot x Drive
Array - Obsolete data
found in Array
Accelerator.
Select F1 to discard
contents of Array
Accelerator.
Select F2 to write
contents of Array
Accelerator to drives.
None
SMART-2 Controller error. Data
found in the array accelerator are
older than data found on drives.
Press
F1
to discard the older
data in the array accelerator
and retain the newer data on
the drives.
1775-Slot x Drive
Array - ProLiant
Storage System Not
Responding SCSI
Port (y): Check
storage system
power switch and
cables. Turn the
system power off
while checking the
ProLiant power and
cable connections,
then turn the system
power back on to
retry.
None
Storage system error
Turn off power to system.
Check the external ProLiant
power switch. External drives
must all be powered up before
or at the same time as the main
system. Check the cables. If a
retry does not help, replace the
cable, ProLiant firmware,
ProLiant backplane, or Smart
Array Controller.
1776-Drive Array -
SCSI Port
Termination Error
None
External and internal SCSI drives
are both configured to port 1.
Reconfigure drives.
1777-Drive Array
External Drive
Subsystem Error
None
Cooling fan failure, internal
temperature alert, or open side
panel
Inspect for cooling fan failure or
open side panel.
1778-Drive Array
resuming Automatic
Data Recovery
process
None
A controller reset or power cycle
occurred during automatic data
recovery.
No action necessary.
1779-Drive Array
Controller detects
replacement drives
None
Intermittent drive failure and/or
possible loss of data
If this message appears and
drive
X
has not been replaced,
an intermittent drive failure has
occurred. This message also
appears once immediately after
drive replacement whenever
data must be restored from the
backup.
1780-Disk 0 Failure
None
Hard drive/format error
Run Diagnostics. Replace the
failed assembly as indicated.
1781-Disk 1 Failure
None
Hard drive/format error
Run Diagnostics. Replace the
failed assembly as indicated.
continued