Compaq ProLiant 6400R Compaq ProLiant 6400R Servers - Page 96

Tape Drive Test Error Codes, Compaq NIC Boards Test Error Codes

Get Compaq ProLiant 6400R PDF manuals and user guides View all Compaq ProLiant 6400R manuals
Add to My Manuals
Save this manual to your list of manuals

Page 96 highlights

Diagnostics and Troubleshooting 3-29 1900 - 1999, Tape Drive Test Error Codes The 1900 series of diagnostic error codes identifies failures with tape cartridges, tape drives, tape drive cabling, adapter boards, and the system board assembly. Table 3-12 Tape Drive Test Error Codes Error Code 1900-xx 1901-xx 1902-xx 1903-xx 1904-xx 1905-xx 1906-xx Description Tape ID failed. Tape servo write failed. Tape format failed. Tape drive sensor test failed. Tape Beginning of Tape/End of Tape (BOT/EOT) test failed. Tape read test failed. Tape write, read, and compare test failed. Recommended Action 1. Replace the tape cartridge and retest. 2. Check and/or replace the signal cable and retest. 3. Check the switch settings on the adapter board (if applicable). 4. Replace the tape adapter board (if applicable) and retest. 5. Replace the tape drive and retest. 6. Replace the system board and retest. 6000 - 6099, Compaq NIC Boards Test Error Codes The 6000 series of diagnostic error codes identifies failures of the Compaq Network Interface Controller. Table 3-13 Compaq NIC Boards Test Error Codes Error Code 6000-xx 6001-xx 6002-xx 6014-xx 6016-xx 6028-xx 6029-xx 6089-xx 6090-xx 6091-xx 6092-xx Description Network card ID failed. Network card setup failed. Network card transmit failed. Network card configuration failed. Network card reset failed. Network card internal failed. Network card external failed. Network card open failed. Network card initialization failed. Network card internal loopback failed. Network card external loopback failed. Recommended Action 1. Check the controller installation in the EISA slot. 2. Check the interrupt type and number setting. 3. Check the media connection at the controller and Multistation Access Unit (MAU). 4. Check the media speed (4/16) and type of Unshielded Twisted Pair/Shielded Twisted Pair (UTP/STP) settings. 5. Check the MAU, cabling, or other network components. 6. Replace the controller.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
Diagnostics and Troubleshooting
3-29
1900
–
1999, Tape Drive Test Error Codes
The 1900 series of diagnostic error codes identifies failures with tape cartridges, tape drives,
tape drive cabling, adapter boards, and the system board assembly.
Table 3-12
Tape Drive Test Error Codes
Error Code
Description
Recommended Action
1900-xx
Tape ID failed.
1901-xx
Tape servo write failed.
1902-xx
Tape format failed.
1903-xx
Tape drive sensor test failed.
1904-xx
Tape Beginning of Tape/End of Tape
(BOT/EOT) test failed.
1905-xx
Tape read test failed.
1906-xx
Tape write, read, and compare test
failed.
1.
Replace the tape cartridge and retest.
2.
Check and/or replace the signal cable and
retest.
3.
Check the switch settings on the adapter
board (if applicable).
4.
Replace the tape adapter board
(if applicable) and retest.
5.
Replace the tape drive and retest.
6.
Replace the system board and retest.
6000
–
6099, Compaq NIC Boards Test Error Codes
The 6000 series of diagnostic error codes identifies failures of the Compaq Network Interface
Controller.
Table 3-13
Compaq NIC Boards Test Error Codes
Error Code
Description
Recommended Action
6000-xx
Network card ID failed.
6001-xx
Network card setup failed.
6002-xx
Network card transmit failed.
6014-xx
Network card configuration failed.
6016-xx
Network card reset failed.
6028-xx
Network card internal failed.
6029-xx
Network card external failed.
6089-xx
Network card open failed.
6090-xx
Network card initialization failed.
6091-xx
Network card internal loopback failed.
6092-xx
Network card external loopback failed.
1.
Check the controller installation in the EISA
slot.
2.
Check the interrupt type and number
setting.
3.
Check the media connection at the
controller and Multistation Access Unit
(MAU).
4.
Check the media speed (4/16) and type of
Unshielded Twisted Pair/Shielded Twisted
Pair (UTP/STP) settings.
5.
Check the MAU, cabling, or other network
components.
6.
Replace the controller.