Compaq ProLiant 6400R Compaq ProLiant 6400R Servers - Page 46

Processor Terminator Module

Get Compaq ProLiant 6400R PDF manuals and user guides View all Compaq ProLiant 6400R manuals
Add to My Manuals
Save this manual to your list of manuals

Page 46 highlights

Removal and Replacement Procedures 2-29 Processor Terminator Module IMPORTANT: If you remove a processor, the processor terminator module must be reinstalled before powering up the server. Failure to have either a processor or processor terminator module installed results in an interlock fault condition that prevents the server from powering up. To remove a processor terminator module, 1. Perform the preparation procedures. See "Preparation Procedures" earlier in this chapter. 2. Remove the top access panel. See "Top Access Panel" earlier in this chapter. 3. Loosen the retention screw . 4. Pull up the two ejector levers securing the processor terminator module in the connector slot . 5. Lift the processor terminator module out of the slot . 2 2 1 3 Figure 2-26. Removing the processor terminator module Reverse steps 1 through 5 to replace the processor terminator module.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
Removal and Replacement Procedures
2-29
Processor Terminator Module
IMPORTANT:
If you remove a processor, the processor terminator module must be reinstalled before
powering up the server. Failure to have either a processor or processor terminator module installed
results in an interlock fault condition that prevents the server from powering up.
To remove a processor terminator module,
1.
Perform the preparation procedures. See
“
Preparation Procedures
”
earlier in this chapter.
2.
Remove the top access panel. See
“
Top Access Panel
”
earlier in this chapter.
3.
Loosen the retention screw
.
4.
Pull up the two ejector levers securing the processor terminator module in the
connector slot
.
5.
Lift the processor terminator module out of the slot
.
2
2
1
3
Figure 2-26.
Removing the processor terminator module
Reverse steps 1 through 5 to replace the processor terminator module.