Compaq ProLiant 6400R Compaq ProLiant 6400R Servers - Page 44

Processor - pentium iii xeon

Get Compaq ProLiant 6400R PDF manuals and user guides View all Compaq ProLiant 6400R manuals
Add to My Manuals
Save this manual to your list of manuals

Page 44 highlights

Removal and Replacement Procedures 2-27 Processor IMPORTANT: When installing a server with Pentium III Xeon processors running at speeds equal to or greater than 550 MHz in Compaq Rack 7000 series racks [part numbers 165753-001 (42U) and 163747-001 (22U)], the new processor technology requires the installation of a new Compaq High Airflow Rack Door Insert [part number 327281-B21 (single) or 327281-B22 (six-pack) for 42U racks and 157847-B21 (single) or 157847-B22 (six-pack) for 22U racks. NOTE: This notice applies to servers with Pentium III Xeon processors running equal to or greater than 550 MHz that will be installed in 7000 series racks. Compaq servers based on other processor technologies, including Pentium III, do not require any rack changes. To remove a processor, 1. Perform the preparation procedures. See "Preparation Procedures" earlier in this chapter. 2. Remove the top access panel. See "Top Access Panel" earlier in this chapter. 3. Loosen the retention screw . 4. Pull up the ejector levers . 5. Lift the processor out of the processor socket . 2 2 1 3 Figure 2-24. Removing a processor Reverse steps 1 through 5 to replace a processor.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
Removal and Replacement Procedures
2-27
Processor
IMPORTANT:
When installing a server with Pentium III Xeon processors running at speeds equal to or
greater than 550 MHz in Compaq Rack 7000 series racks [part numbers 165753-001 (42U) and
163747-001 (22U)], the new processor technology requires the installation of a new Compaq High
Airflow Rack Door Insert [part number 327281-B21 (single) or 327281-B22 (six-pack) for 42U racks and
157847-B21 (single) or 157847-B22 (six-pack) for 22U racks.
NOTE:
This notice applies to servers with Pentium III Xeon processors running equal to or greater than
550 MHz that will be installed in 7000 series racks. Compaq servers based on other processor
technologies, including Pentium III, do not require any rack changes.
To remove a processor,
1.
Perform the preparation procedures. See
“
Preparation Procedures
”
earlier in this chapter.
2.
Remove the top access panel. See
“
Top Access Panel
”
earlier in this chapter.
3.
Loosen the retention screw
.
4.
Pull up the ejector levers
.
5.
Lift the processor out of the processor socket
.
2
3
2
1
Figure 2-24.
Removing a processor
Reverse steps 1 through 5 to replace a processor
.