Home » Dell Manuals » Hubs & Switches » Dell PowerConnect 5324 » Manual Viewer

Dell PowerConnect 5324 User's Guide - Page 24

Layer 3 Features, Quality of Service Features, For more information on DHCP - vlan setup

View all Dell PowerConnect 5324 manuals

Add to My Manuals
Save this manual to your list of manuals

Page 24 highlights

www.dell.com | support.dell.com LAG is composed of ports with the same speed, set to full-duplex operation. For more information, see "Defining LAG Membership". Link Aggregation and LACP LACP uses peer exchanges across links to determine, on an ongoing basis, the aggregation capability of various links, and continuously provides the maximum level of aggregation capability achievable between a given pair of systems. LACP automatically determines, configures, binds and monitors the port binding to aggregators within the system. For more information, see "Defining LACP Parameters". Layer 3 Features Address Resolution Protocol (ARP) ARP is a TCP/IP protocol that converts IP addresses into physical addresses. ARP automatically determines Device Next-Hop MAC addresses of systems, including directly attached end systems. Users can override and supplement this by defining additional ARP Table entries. For more information, see "Mapping Domain Host". TCP Transport Control Protocol (TCP) connections are defined between 2 ports by an initial synchronization exchange. TCP ports are identified by an IP address and a 16-bit port number. Octets streams are divided into TCP packets, each carrying a sequence number. BootP and DHCP Clients Dynamic Host Configuration Protocol (DHCP) enables additional setup parameters to be received from a network server upon system startup. DHCP service is an on-going process. DHCP is an extension to BootP. For more information on DHCP, see "Defining DHCP IP Interface Parameters". Quality of Service Features Class Of Service 802.1p Support The IEEE 802.1p signaling technique is an OSI Layer 2 standard for marking and prioritizing network traffic at the data link/MAC sub-layer. 802.1p traffic is classified and sent to the destination. No bandwidth reservations or limits are established or enforced. 802.1p is a spin-off of the 802.1Q (VLANs) standard. 802.1p establishes eight levels of priority, similar to the IP Precedence IP Header bit-field. For more information, see "Configuring Quality of Service". 24 Introduction

Section	Page
Introduction	19
PowerConnect 5324	19
Features	19
General Features	20
MAC Address Supported Features	21
Layer 2 Features	21
VLAN Supported Features	22
Spanning Tree Protocol Features	23
Link Aggregation	23
Layer 3 Features	24
Quality of Service Features	24
Device Management Features	25
Security Features	26
Locked Port Support	26
Additional CLI Documentation	27
Hardware Description	29
Device Port Configurations	29
PowerConnect 5324 Front Panel Port Description	29
PowerConnect Back Panel Port Description	30
Device Ports	30
Physical Dimensions	31
LED Definitions	31
Port LEDs	31
System LEDs	32
Hardware Components	33
Power Supplies	33
Reset Button	34
Ventilation System	34
Installing the PowerConnect Device	35
Installation Precautions	35
Site Requirements	36
Unpacking	36
Package Contents	36
Unpacking the Device	36
Mounting the Device	37
Overview	37
Mounting the System	37
Installing the Device without a Rack	38
Connecting the Device	38
Connecting a Device to a Terminal	38
Connecting a Device to a Power Supply	39
Port Connections, Cables, and Pinout Information	40
RJ-45 Connections for 10/100/1000BaseT Ports	40
Port Default Settings	41
Auto-Negotiation	41
MDI/MDIX	42
Flow Control	42
Back Pressure	42
Switching Port Default Settings	42
Starting and Configuring the Device	43
Configure the Terminal	43
Booting the Device	44
Configuration Overview	48
Initial Configuration	48
Static IP Address and Subnet Mask	49
Static Route Configuration	49
Assigning Static IP Addresses on an Inband Interface	49
Verifying the IP and Default Gateway Addresses	50
User Name	50
SNMP Community Strings	51
Configuring SNMP	52
Viewing SNMP Community Tables	52
Advanced Configuration	53
Retrieving an IP Address From a DHCP Server	53
Receiving an IP Address From a BOOTP Server	55
Security Management and Password Configuration	56
Configuring Security Passwords	56
Configuring an Initial Terminal Password	57
Configuring an Initial Telnet Password	57
Configuring an Initial SSH Password	57
Configuring an Initial HTTP Password	58
Configuring an Initial HTTPS Password	58
Startup Procedures	58
Startup Menu Procedures	58
Software Download	60
Erase FLASH File	60
Erasing the Device Configuration	60
Password Recovery	61
Software Download Through TFTP Server	61
Using Dell OpenManage Switch Administrator	65
Understanding the Interface	65
Device Representation	66
Using the Switch Administrator Buttons	67
Information Buttons	67
Device Management Buttons	67
Starting the Application	68
Accessing the Device Through the CLI	68
Console Connection	69
Telnet Connection	69
Using the CLI	70
Command Mode Overview	70
User EXEC Mode	70
Privileged EXEC Mode	70
Global Configuration Mode	71
Interface Configuration Mode	72
CLI Examples	73
Configuring System Information	75
Defining General Device Information	76
Viewing the Asset Page	76
Viewing System Health Information	85
Viewing the Versions Page	87
Resetting the Device	89
Configuring SNTP Settings	90
Polling for Unicast Time Information	91
Polling for Anycast Time Information	91
Broadcast Time Information	91
Defining SNTP Global Parameters	92
Defining SNTP Authentication Methods	93
Defining SNTP Servers	96
Defining SNTP Interfaces	101
Managing Logs	104
Defining Global Log Parameters	104
Displaying RAM Log Table	108
Displaying the Log File Table	111
Configuring the Remote Log Server Settings Page	115
Defining Device IP Addresses	119
Defining Default Gateways	119
Defining IP Interfaces	120
Defining DHCP IP Interface Parameters	123
Configuring Domain Name Systems	127
Defining Default Domains	130
Mapping Domain Host	132
Configuring ARP	134
Running Cable Diagnostics	139
Viewing Copper Cable Diagnostics	139
Viewing Optical Transceiver Diagnostics	141
Managing Device Security	145
Defining Access Profiles	145
Defining Authentication Profiles	151
Assigning Authentication Profiles	155
Defining the Local User Databases	159
Defining Line Passwords	162
Defining Enable Password	164
Defining TACACS+ Settings	165
Configuring RADIUS Global Parameters	170
Defining SNMP Parameters	177
Defining Communities	177
Defining Traps	182
Managing Files	186
File Management Overview	186
Downloading Files	187
Uploading Files	189
Copying Files	191
Defining Advanced Settings	193
Configuring General Device Tuning Parameters	193
Configuring Device Information	197
Configuring Network Security	197
Network Security Overview	197
Configuring Port Based Authentication	199
Configuring Advanced Port Based Authentication	203
Authenticating Users	207
Configuring Port Security	209
Configuring Ports	214
Defining Port Parameters	214
Defining LAG Parameters	221
Enabling Storm Control	225
Defining Port Mirroring Sessions	228
Configuring Address Tables	231
Defining Static Addresses	231
Viewing Dynamic Addresses	234
Configuring GARP	237
Defining GARP Timers	237
Configuring the Spanning Tree Protocol	240
Defining STP Global Settings	240
Defining STP Port Settings	244
Defining STP LAG Settings	249
Configuring Rapid Spanning Tree	251
Configuring VLANs	254
Defining VLAN Members	255
Defining VLAN Ports Settings	261
Defining VLAN LAG Settings	264
Defining VLAN Protocol Groups	267
Adding Protocol Ports	269
Configuring GVRP	270
Aggregating Ports	274
Defining LACP Parameters	275
Defining LAG Membership	278
Multicast Forwarding Support	279
Defining Multicast Global Parameters	279
Adding Bridge Multicast Address Members	282
Assigning Multicast Forward All Parameters	287
IGMP Snooping	290
Viewing Statistics	295
Viewing Tables	296
Viewing Utilization Summary	296
Viewing Counter Summary	298
Viewing Interface Statistics	299
Viewing Etherlike Statistics	302
Viewing GVRP Statistics	306
Viewing RMON Statistics	313
Viewing RMON Statistics Group	313
Viewing RMON History Control Statistics	316
Viewing the RMON History Table	318
Defining Device RMON Events	321
Viewing the RMON Events Log	324
Defining RMON Device Alarms	326
Viewing Charts	330
Viewing Port Statistics	330
Viewing LAG Statistics	332
Configuring Quality of Service	335
Quality of Service (QoS) Overview	336
CoS Services	337
Defining CoS Global Parameters	339
Configuring QoS Global Settings	339
Defining QoS Interface Settings	341
Defining Queue Settings	344
Mapping CoS Values to Queues	347
Mapping DSCP Values to Queues	349
Device Specifications	351
Port and Cable Specifications	351
Port Specifications	351
Operating Conditions	352
Physical Device Specifications	352
Device Memory Specifications	352
Feature Specifications	353
VLAN	353
Quality of Service	353
Layer 2 Multicast	353
Device Security	353
Additional Switching Features	353

Match case Limit results 1 per page

Introduction

www.dell.com | support.dell.com

LAG is composed of ports with the same speed, set to full-duplex operation.

For more information, see "Defining LAG Membership".

Link Aggregation and LACP

LACP uses peer exchanges across links to determine, on an ongoing basis, the aggregation

capability of various links, and continuously provides the maximum level of aggregation capability

achievable between a given pair of systems. LACP automatically determines, configures, binds and

monitors the port binding to aggregators within the system.

For more information, see "Defining LACP Parameters".

Layer 3 Features

Address Resolution Protocol (ARP)

ARP is a TCP/IP protocol that converts IP addresses into physical addresses. ARP automatically

determines Device Next-Hop MAC addresses of systems, including directly attached end systems.

Users can override and supplement this by defining additional ARP Table entries.

For more information, see "Mapping Domain Host".

TCP

Transport Control Protocol (TCP) connections are defined between 2 ports by an initial

synchronization exchange. TCP ports are identified by an IP address and a 16-bit port number.

Octets streams are divided into TCP packets, each carrying a sequence number.

BootP and DHCP Clients

Dynamic Host Configuration Protocol (DHCP) enables additional setup parameters to be received

from a network server upon system startup. DHCP service is an on-going process. DHCP is an

extension to BootP.

For more information on DHCP, see "Defining DHCP IP Interface Parameters".

Quality of Service Features

Class Of Service 802.1p Support

The IEEE 802.1p signaling technique is an OSI Layer 2 standard for marking and prioritizing

network traffic at the data link/MAC sub-layer. 802.1p traffic is classified and sent to the

destination. No bandwidth reservations or limits are established or enforced. 802.1p is a spin-off of

the 802.1Q (VLANs) standard. 802.1p establishes eight levels of priority, similar to the IP

Precedence IP Header bit-field.

For more information, see "Configuring Quality of Service".