Dell PowerVault DL2200 Hardware Owner's Manual - Page 97

Installing the Storage Controller Card, card into the black card-edge guide.

Get Dell PowerVault DL2200 PDF manuals and user guides View all Dell PowerVault DL2200 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 97 highlights

Installing the Storage Controller Card CAUTION: Many repairs may only be done by a certified service technician. You should only perform troubleshooting and simple repairs as authorized in your product documentation, or as directed by the online or telephone service and support team. Damage due to servicing that is not authorized by Dell is not covered by your warranty. Read and follow the safety instructions that came with the product. 1 Turn off the system, including any attached peripherals, and disconnect the system from the electrical outlet. 2 Open the system. See "Opening the System" on page 64. 3 If installed, remove the expansion card. See "Removing an Expansion Card" on page 92. 4 Route the cables in the cable path under the storage controller card slot on the expansion card riser. 5 With the storage controller card edge facing the riser, insert one side of the card into the black card-edge guide. NOTE: For expansion-card riser 1, the installation sequence must be slot 3, 2, 1, and 4. The storage controller card must be installed in Slot 4 after the other expansion cards have been installed. 6 Bend outward on the blue card-edge guide, lower the card onto the blue card-edge guide, and release the guide. See Figure 3-15. 7 Slide the storage controller's card edge connector into the card slot on the riser until the card is fully seated. 8 Connect the two SAS data cable connectors, CNTRL 0 and CNTRL 1, to the storage controller card. See Figure 3-15. NOTE: Ensure to connect the cables according to the connector labels on the cable. The cable does not function properly if reversed. 9 For a battery-cached RAID controller, connect the RAID battery cable to the controller card. Installing System Components 97

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
Installing System Components
97
Installing the Storage Controller Card
CAUTION:
Many repairs may only be done by a certified service technician.
You should only perform troubleshooting and simple repairs as authorized in
your product documentation, or as directed by the online or telephone service and
support team. Damage due to servicing that is not authorized by Dell is not
covered by your warranty. Read and follow the safety instructions that came
with the product.
1
Turn off the system, including any attached peripherals, and disconnect
the system from the electrical outlet.
2
Open the system. See "Opening the System" on page 64.
3
If installed, remove the expansion card. See "Removing an Expansion
Card" on page 92.
4
Route the cables in the cable path under the storage controller card slot on
the expansion card riser.
5
With the storage controller card edge facing the riser, insert one side of the
card into the black card-edge guide.
NOTE:
For expansion-card riser 1, the installation sequence must be
slot 3, 2, 1, and 4. The storage controller card must be installed in Slot 4 after
the other expansion cards have been installed.
6
Bend outward on the blue card-edge guide, lower the card onto the blue
card-edge guide, and release the guide. See Figure 3-15.
7
Slide the storage controller’s card edge connector into the card slot on the
riser until the card is fully seated.
8
Connect the two SAS data cable connectors, CNTRL 0 and CNTRL 1, to
the storage controller card. See Figure 3-15.
NOTE:
Ensure to connect the cables according to the connector labels on the
cable. The cable does not function properly if reversed.
9
For a battery-cached RAID controller, connect the RAID battery cable to
the controller card.