HP Scanjet Enterprise 7000n HP Scanjet 7000n Series - User Guide - Page 23

Table 2-2, Menu item, Sub-menu item, Values and Description

Get HP Scanjet Enterprise 7000n - Document Capture Workstation PDF manuals and user guides View all HP Scanjet Enterprise 7000n manuals
Add to My Manuals
Save this manual to your list of manuals

Page 23 highlights

Table 2-2 Jetdirect menus (continued) Menu item Sub-menu item Reset Security Sub-menu item Link Speed Values and Description Specify whether the current security settings on the Jetdirect server will be saved or reset to factory defaults. No (default): The current security settings are maintained. Yes: Security settings are reset to factory defaults. The link speed and communication mode of the Jetdirect server must match the network. The available settings depend on the product and installed Jetdirect server. Select one of the following link configuration settings: CAUTION: If you change the link setting, network communications with the Jetdirect server and network product might be lost. Auto (default): The Jetdirect server uses autonegotiation to configure itself with the highest link speed and communication mode allowed. If autonegotiation fails, either the 100TX Half value or the 10T Half value is set depending on the detected link speed of the hub/switch port. (A 1000T half-duplex selection is not supported.) 10T Half: 10 Mbps, half-duplex operation. 10T Full: 10 Mbps, Full-duplex operation. 100TX Half: 100 Mbps, half-duplex operation. 100TX Full: 100 Mbps, full-duplex operation. 100TX Auto: Limits auto-negotiation to a maximum link speed of 100 Mbps. 1000TX Full: 1000 Mbps, full-duplex operation. ENWW Navigate the Administration menu 15

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
Menu item
Sub-menu item
Sub-menu item
Values and Description
Reset Security
Specify whether the current security settings on the
Jetdirect server will be saved or reset to factory
defaults.
No
(default): The current security settings are
maintained.
Yes
: Security settings are reset to factory defaults.
Link Speed
The link speed and communication mode of the
Jetdirect server must match the network. The available
settings depend on the product and installed Jetdirect
server. Select one of the following link configuration
settings:
CAUTION:
If you change the link setting, network
communications with the Jetdirect server and network
product might be lost.
Auto
(default): The Jetdirect server uses auto-
negotiation to configure itself with the highest link
speed and communication mode allowed. If auto-
negotiation fails, either the
100TX Half
value or the
10T
Half
value is set depending on the detected link speed
of the hub/switch port. (A 1000T half-duplex selection
is not supported.)
10T Half
: 10 Mbps, half-duplex operation.
10T Full
: 10 Mbps, Full-duplex operation.
100TX Half
: 100 Mbps, half-duplex operation.
100TX Full
: 100 Mbps, full-duplex operation.
100TX Auto
: Limits auto-negotiation to a maximum link
speed of 100 Mbps.
1000TX Full
: 1000 Mbps, full-duplex operation.
Table 2-2
Jetdirect menus (continued)
ENWW
Navigate the Administration menu
15