HP Scanjet Enterprise 7000n HP Scanjet 7000n Series - User Guide - Page 35

Disable network protocols (optional), Link speed and duplex settings

Get HP Scanjet Enterprise 7000n - Document Capture Workstation PDF manuals and user guides View all HP Scanjet Enterprise 7000n manuals
Add to My Manuals
Save this manual to your list of manuals

Page 35 highlights

Disable network protocols (optional) By factory default, all supported network protocols are enabled. Disabling unused protocols has the following benefits: ● Decreases product-generated network traffic ● Provides only pertinent information on the configuration page ● Allows the product control panel to display protocol-specific error and warning messages Link speed and duplex settings The link speed and communication mode of the product must match the network. For most situations, leave the product in automatic mode. Incorrect changes to the link speed and duplex settings might prevent the product from communicating with other network devices. If you need to make changes, use the product control panel. NOTE: Making changes to these settings causes the product to turn off and then on. Make changes only when the product is idle. 1. At the product control panel, touch the Administration button. 2. Touch the Initial Setup menu to open it. 3. Touch the Networking and I/O menu to open it. 4. Touch the option for the Jetdirect menu. 5. Touch the down arrow until the option for link speed displays. 6. Touch the option for link speed. 7. Touch one of the following options. Setting Auto 10T Half 10T Full 100TX Half 100TX Full 100TX Auto 1000TX Full Description The product automatically configures itself for the highest link speed and communication mode allowed on the network. 10 megabytes per second (Mbps), half-duplex operation 10 Mbps, full-duplex operation 100 Mbps, half-duplex operation 100 Mbps, full-duplex operation Limits auto-negotiation to a maximum link speed of 100 Mbps 1000 Mbps, full-duplex operation 8. Touch the Save button. The product turns off and then on. ENWW Configure the product to use the network 27

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
Disable network protocols (optional)
By factory default, all supported network protocols are enabled. Disabling unused protocols has the
following benefits:
●
Decreases product-generated network traffic
●
Provides only pertinent information on the configuration page
●
Allows the product control panel to display protocol-specific error and warning messages
Link speed and duplex settings
The link speed and communication mode of the product must match the network. For most situations,
leave the product in automatic mode. Incorrect changes to the link speed and duplex settings might
prevent the product from communicating with other network devices. If you need to make changes, use
the product control panel.
NOTE:
Making changes to these settings causes the product to turn off and then on. Make changes
only when the product is idle.
1.
At the product control panel, touch the
Administration
button.
2.
Touch the
Initial Setup
menu to open it.
3.
Touch the
Networking and I/O
menu to open it.
4.
Touch the option for the Jetdirect menu.
5.
Touch the down arrow until the option for link speed displays.
6.
Touch the option for link speed.
7.
Touch one of the following options.
Setting
Description
Auto
The product automatically configures itself for the highest link speed and
communication mode allowed on the network.
10T Half
10 megabytes per second (Mbps), half-duplex operation
10T Full
10 Mbps, full-duplex operation
100TX Half
100 Mbps, half-duplex operation
100TX Full
100 Mbps, full-duplex operation
100TX Auto
Limits auto-negotiation to a maximum link speed of 100 Mbps
1000TX Full
1000 Mbps, full-duplex operation
8.
Touch the
Save
button. The product turns off and then on.
ENWW
Configure the product to use the network
27