Home » Intel Manuals » Processors » Intel E6700 » Manual Viewer

Intel E6700 Mechanical Design Guidelines - Page 118

ATX Reference Clip - Sheet 1

UPC - 735858184618

Add to My Manuals
Save this manual to your list of manuals

Page 118 highlights

Mechanical Drawings Figure 7-48. ATX Reference Clip - Sheet 1 8 7 6 5 H 4 3 2 DWG. NO C85609 SHT. 1 REV B H 94.62 [ 3.725 ] 7 G REMOVE ALL BURRS OR SHARP EDGES AROUND PERIMETER OF PART. SHARPNESS OF EDGES SUBJECT TO HANDLING ARE REQUIRED TO MEET THE UL1439 TEST. G 4X 10 0.2 [ .394 .007 ] 0.5 [.019] A B F 36.44 0.2 7 [ 1.435 .007 ] F A E SEE DETAIL A A E NOTES: 94.62 [ 3.725 ] 7 D PERMANENTLY MARK PART NUMBER AND REVISION LEVEL APPROXIMATELY WHERE SHOWN XXXXXX-XXX REV XX B C D 1. THIS DRAWING TO BE USED IN CONJUNTION WITH SUPPLIED 3D DATABASE FILE. ALL DIMENSIONS AND TOLERANCES ON THIS DRAWING TAKE PRECEDENCE OVER SUPPLIED FILE AND ARE APPLICABLE AT PART FREE, UNCONSTRAINED STATE UNLESS INDICATED OTHERWISE. 2. MATERIAL: D A) TYPE: AISI 1065 COLD DRAWN STEEL OR EQUIVALENT D 1.6MM THICKNESS B) CRITICAL MECHANICAL MATERIAL PROPERTIES FOR EQUIVALENT MATERIAL SELECTION: ELASTIC MODULUS > 206.8 GPA [29,900 KSI] MIN TENSILE YIELD STRENGTH (ASTM D638) > 490 MPa [71KSI] SQ 53.5 0.2 C) MASS - 35.4 GRAMS (REF) [ 2.106 .007 ] 3. SECONDARY OPERATIONS: 0.5 [.019] A B A) FINISH: NICKEL PLATE REQUIRED AFTER FORMING 4. ALL DIMENSIONS AND TOLERANCES ARE SHOWN AFTER PLATING C 5 PUNCH DIRECTION 6. BREAK ALL SHARP CORNERS AND BURRS 7 CRITICAL TO FUNCTION DIMENSION 8 COINING REQUIRED AS SPECIFIED 9. SECONDARY UNIT TOLERANCES SHOULD BE CALCULATED FROM PRIMARY 5 UNITS TO AVOID ROUND OFF ERROR. SEE DETAIL C B 39.6 [ 1.559 ] 2 0.2 [ .079 .007 ] B TOP C85609-001 CLIP, STEEL, STAMPED QTY ITEM NO PART NUMBER DESCRIPTION PARTS LIST SECTION A-A A SEE DETAIL B 7 3.52 0.2 [ .139 .007 ] UNLESS OTHERWISE SPECIFIED INTERPRET DIMENSIONS AND TOLERANCES IN ACCORDANCE WITH ASME Y14.5M-1994 DIMENSIONS ARE IN MILLIMETERS ALL UNTOLERANCED LINEAR DIMENSIONS ± 0.1 ANGLES ± 0.5 THIRD ANGLE PROJECTION DEPARTMENT TMD TITLE R 2200 MISSION COLLEGE BLVD. CORP. P.O. BOX 58119 SANTA CLARA, CA 95052-8119 RCFH4 HS CLIP, 35mm core SIZE DRAWING NUMBER A1 C85609 REV A B SCALE: NONE DO NOT SCALE DRAWING SHEET 1 OF 2 8 7 6 5 4 3 2 1 118 Thermal and Mechanical Design Guidelines

Section	Page
1 Introduction	9
1.1 Document Goals and Scope	9
1.1.1 Importance of Thermal Management	9
1.1.2 Document Goals	9
1.1.3 Document Scope	10
1.2 References	11
1.3 Definition of Terms	11
2 Processor Thermal/Mechanical Information	13
2.1 Mechanical Requirements	13
2.1.1 Processor Package	13
2.1.2 Heatsink Attach	15
2.1.2.1 General Guidelines	15
2.1.2.2 Heatsink Clip Load Requirement	15
2.1.2.3 Additional Guidelines	16
2.2 Thermal Requirements	16
2.2.1 Processor Case Temperature	16
2.2.2 Thermal Profile	17
2.2.3 Thermal Solution Design Requirements	17
2.2.4 TCONTROL	18
2.3 Heatsink Design Considerations	19
2.3.1 Heatsink Size	20
2.3.2 Heatsink Mass	20
2.3.3 Package IHS Flatness	21
2.3.4 Thermal Interface Material	21
2.4 System Thermal Solution Considerations	22
2.4.1 Chassis Thermal Design Capabilities	22
2.4.2 Improving Chassis Thermal Performance	22
2.4.3 Summary	23
2.5 System Integration Considerations	23
3 Thermal Metrology	25
3.1 Characterizing Cooling Performance Requirements	25
3.1.1 Example	26
3.2 Processor Thermal Solution Performance Assessment	27
3.3 Local Ambient Temperature Measurement Guidelines	27
3.4 Processor Case Temperature Measurement Guidelines	30
4 Thermal Management Logic and Thermal Monitor Feature	31
4.1 Processor Power Dissipation	31
4.2 Thermal Monitor Implementation	31
4.2.1 PROCHOT# Signal	32
4.2.2 Thermal Control Circuit	32
4.2.2.1 Thermal Monitor	32
4.2.3 Thermal Monitor 2	33
4.2.4 Operation and Configuration	34
4.2.5 On-Demand Mode	35
4.2.6 System Considerations	35
4.2.7 Operating System and Application Software Considerations	36
4.2.8 THERMTRIP# Signal	36
4.2.9 Cooling System Failure Warning	36
4.2.10 Digital Thermal Sensor	37
4.2.11 Platform Environmental Control Interface (PECI)	38
5 Balanced Technology Extended (BTX) Thermal/Mechanical Design Information	39
5.1 Overview of the BTX Reference Design	39
5.1.1 Target Heatsink Performance	39
5.1.2 Acoustics	40
5.1.3 Effective Fan Curve	41
5.1.4 Voltage Regulator Thermal Management	42
5.1.5 Altitude	43
5.1.6 Reference Heatsink Thermal Validation	43
5.2 Environmental Reliability Testing	43
5.2.1 Structural Reliability Testing	43
5.2.1.1 Random Vibration Test Procedure	43
5.2.1.2 Shock Test Procedure	44
5.2.2 Power Cycling	45
5.2.3 Recommended BIOS/CPU/Memory Test Procedures	46
5.3 Material and Recycling Requirements	46
5.4 Safety Requirements	47
5.5 Geometric Envelope for Intel® Reference BTX Thermal Module Assembly	47
5.6 Preload and TMA Stiffness	48
5.6.1 Structural Design Strategy	48
5.6.2 TMA Preload verse Stiffness	48
6 ATX Thermal/Mechanical Design Information	51
6.1 ATX Reference Design Requirements	51
6.2 Validation Results for Reference Design	53
6.2.1 Heatsink Performance	53
6.2.2 Acoustics	54
6.2.3 Altitude	54
6.2.4 Heatsink Thermal Validation	55
6.3 Environmental Reliability Testing	55
6.3.1 Structural Reliability Testing	55
6.3.1.1 Random Vibration Test Procedure	55
6.3.1.2 Shock Test Procedure	56
6.3.2 Power Cycling	57
6.3.3 Recommended BIOS/CPU/Memory Test Procedures	58
6.4 Material and Recycling Requirements	58
6.5 Safety Requirements	59
6.6 Geometric Envelope for Intel® Reference ATX Thermal Mechanical Design	59
6.7 Reference Attach Mechanism	60
6.7.1 Structural Design Strategy	60
6.7.2 Mechanical Interface to the Reference Attach Mechanism	61
7 Intel® Quiet System Technology (Intel® QST)	63
7.1 Intel® QST Algorithm	63
7.1.1 Output Weighting Matrix	64
7.1.2 Proportional-Integral-Derivative (PID)	64
7.2 Board and System Implementation of Intel® QST	66
7.3 Intel® QST Configuration and Tuning	68

Match case Limit results 1 per page

Mechanical Drawings

118

Thermal and Mechanical Design Guidelines

Figure 7-48. ATX Reference Clip – Sheet 1

0.2

.079

.007

[

]

3.52

0.2

.139

.007

[

]

94.62

3.725

[

]

SQ 53.5

0.2

2.106

.007

[

]

94.62

3.725

[

]

4X 10

0.2

.394

.007

[

]

39.6

1.559

[

]

36.44

0.2

1.435

.007

[

]

C85609

DWG. NO

SHT.

REV

DEPARTMENT

CORP.

2200 MISSION COLLEGE BLVD.

P.O. BOX 58119

SANTA CLARA, CA 95052-8119

TMD

TITLE

RCFH4 HS CLIP, 35mm core

SIZE

DRAWING NUMBER

REV

C85609

SCALE:

NONE

DO NOT SCALE DRAWING

SHEET

UNLESS OTHERWISE SPECIFIED

INTERPRET DIMENSIONS AND TOLERANCES

IN ACCORDANCE WITH ASME Y14.5M-1994

DIMENSIONS ARE IN MILLIMETERS

ALL UNTOLERANCED LINEAR

DIMENSIONS ±

0.1

ANGLES ±

0.5

THIRD ANGLE PROJECTION

PARTS LIST

DESCRIPTION

PART NUMBER

ITEM NO

QTY

CLIP, STEEL, STAMPED

C85609-001

TOP

0.5 [.019]

NOTES:

1. THIS DRAWING TO BE USED IN CONJUNTION WITH SUPPLIED 3D

DATABASE FILE. ALL DIMENSIONS AND TOLERANCES ON THIS

DRAWING TAKE PRECEDENCE OVER SUPPLIED FILE AND ARE

APPLICABLE AT PART FREE, UNCONSTRAINED STATE UNLESS

INDICATED OTHERWISE.

2. MATERIAL:

A) TYPE: AISI 1065 COLD DRAWN STEEL OR EQUIVALENT

1.6MM THICKNESS

B) CRITICAL MECHANICAL MATERIAL PROPERTIES

FOR EQUIVALENT MATERIAL SELECTION:

ELASTIC MODULUS > 206.8 GPA [29,900 KSI]

MIN TENSILE YIELD STRENGTH (ASTM D638) >

490 MPa [71KSI]

C) MASS - 35.4 GRAMS (REF)

3. SECONDARY OPERATIONS:

A) FINISH: NICKEL PLATE REQUIRED AFTER FORMING

4. ALL DIMENSIONS AND TOLERANCES ARE SHOWN AFTER PLATING

PUNCH DIRECTION

6. BREAK ALL SHARP CORNERS AND BURRS

CRITICAL TO FUNCTION DIMENSION

COINING REQUIRED AS SPECIFIED

9. SECONDARY UNIT TOLERANCES SHOULD BE CALCULATED FROM PRIMARY

UNITS TO AVOID ROUND OFF ERROR.

REMOVE ALL BURRS OR SHARP EDGES AROUND PERIMETER OF PART.

SHARPNESS OF EDGES SUBJECT TO HANDLING ARE REQUIRED TO

MEET THE UL1439 TEST.

PERMANENTLY MARK PART

NUMBER AND REVISION LEVEL

APPROXIMATELY WHERE SHOWN

XXXXXX-XXX REV XX

SEE DETAIL

SECTION

A-A

SEE DETAIL