Home » Intel Manuals » Processors » Intel E6700 » Manual Viewer

Intel E6700 Mechanical Design Guidelines - Page 37

Digital Thermal Sensor

UPC - 735858184618

Add to My Manuals
Save this manual to your list of manuals

Page 37 highlights

Thermal Management Logic and Thermal Monitor Feature 4.2.10 Digital Thermal Sensor Multiple digital thermal sensors can be implemented within the package without adding a pair of signal pins per sensor as required with the thermal diode. The digital thermal sensor is easier to place in thermally sensitive locations of the processor than the thermal diode. This is achieved due to a smaller foot print and decreased sensitivity to noise. Since the DTS is factory set on a per-part basis there is no need for the health monitor components to be updated at each processor family. The processor uses the Digital Thermal Sensor (DTS) as the on-die sensor to use for fan speed control (FSC). The DTS is monitoring the same sensor that activates the TCC (see Section 4.2.2). Readings from the DTS are relative to the activation of the TCC. The DTS value where TCC activation occurs is 0 (zero). A TCONTROL value will be provided for use with DTS. The usage model for TCONTROL with the DTS as below: • If the Digital thermal sensor reading is less than TCONTROL, the fan speed can be reduced. • If the Digital thermal sensor reading is greater than or equal to TCONTROL, then TC must be maintained at or below the Thermal Profile for the measured power dissipation. The DTS TCONTROL value is factory configured and is written into TOFFSET MSR. The BIOS can read the TOFFSET MSR and provide this value to the fan speed control device. Figure 4-3. TCONTROL for Digital Thermal Sensor Note: The processor has only DTS and no thermal diode. The TCONTROL in the MSR is relevant only to the DTS. Thermal and Mechanical Design Guidelines 37

Section	Page
1 Introduction	9
1.1 Document Goals and Scope	9
1.1.1 Importance of Thermal Management	9
1.1.2 Document Goals	9
1.1.3 Document Scope	10
1.2 References	11
1.3 Definition of Terms	11
2 Processor Thermal/Mechanical Information	13
2.1 Mechanical Requirements	13
2.1.1 Processor Package	13
2.1.2 Heatsink Attach	15
2.1.2.1 General Guidelines	15
2.1.2.2 Heatsink Clip Load Requirement	15
2.1.2.3 Additional Guidelines	16
2.2 Thermal Requirements	16
2.2.1 Processor Case Temperature	16
2.2.2 Thermal Profile	17
2.2.3 Thermal Solution Design Requirements	17
2.2.4 TCONTROL	18
2.3 Heatsink Design Considerations	19
2.3.1 Heatsink Size	20
2.3.2 Heatsink Mass	20
2.3.3 Package IHS Flatness	21
2.3.4 Thermal Interface Material	21
2.4 System Thermal Solution Considerations	22
2.4.1 Chassis Thermal Design Capabilities	22
2.4.2 Improving Chassis Thermal Performance	22
2.4.3 Summary	23
2.5 System Integration Considerations	23
3 Thermal Metrology	25
3.1 Characterizing Cooling Performance Requirements	25
3.1.1 Example	26
3.2 Processor Thermal Solution Performance Assessment	27
3.3 Local Ambient Temperature Measurement Guidelines	27
3.4 Processor Case Temperature Measurement Guidelines	30
4 Thermal Management Logic and Thermal Monitor Feature	31
4.1 Processor Power Dissipation	31
4.2 Thermal Monitor Implementation	31
4.2.1 PROCHOT# Signal	32
4.2.2 Thermal Control Circuit	32
4.2.2.1 Thermal Monitor	32
4.2.3 Thermal Monitor 2	33
4.2.4 Operation and Configuration	34
4.2.5 On-Demand Mode	35
4.2.6 System Considerations	35
4.2.7 Operating System and Application Software Considerations	36
4.2.8 THERMTRIP# Signal	36
4.2.9 Cooling System Failure Warning	36
4.2.10 Digital Thermal Sensor	37
4.2.11 Platform Environmental Control Interface (PECI)	38
5 Balanced Technology Extended (BTX) Thermal/Mechanical Design Information	39
5.1 Overview of the BTX Reference Design	39
5.1.1 Target Heatsink Performance	39
5.1.2 Acoustics	40
5.1.3 Effective Fan Curve	41
5.1.4 Voltage Regulator Thermal Management	42
5.1.5 Altitude	43
5.1.6 Reference Heatsink Thermal Validation	43
5.2 Environmental Reliability Testing	43
5.2.1 Structural Reliability Testing	43
5.2.1.1 Random Vibration Test Procedure	43
5.2.1.2 Shock Test Procedure	44
5.2.2 Power Cycling	45
5.2.3 Recommended BIOS/CPU/Memory Test Procedures	46
5.3 Material and Recycling Requirements	46
5.4 Safety Requirements	47
5.5 Geometric Envelope for Intel® Reference BTX Thermal Module Assembly	47
5.6 Preload and TMA Stiffness	48
5.6.1 Structural Design Strategy	48
5.6.2 TMA Preload verse Stiffness	48
6 ATX Thermal/Mechanical Design Information	51
6.1 ATX Reference Design Requirements	51
6.2 Validation Results for Reference Design	53
6.2.1 Heatsink Performance	53
6.2.2 Acoustics	54
6.2.3 Altitude	54
6.2.4 Heatsink Thermal Validation	55
6.3 Environmental Reliability Testing	55
6.3.1 Structural Reliability Testing	55
6.3.1.1 Random Vibration Test Procedure	55
6.3.1.2 Shock Test Procedure	56
6.3.2 Power Cycling	57
6.3.3 Recommended BIOS/CPU/Memory Test Procedures	58
6.4 Material and Recycling Requirements	58
6.5 Safety Requirements	59
6.6 Geometric Envelope for Intel® Reference ATX Thermal Mechanical Design	59
6.7 Reference Attach Mechanism	60
6.7.1 Structural Design Strategy	60
6.7.2 Mechanical Interface to the Reference Attach Mechanism	61
7 Intel® Quiet System Technology (Intel® QST)	63
7.1 Intel® QST Algorithm	63
7.1.1 Output Weighting Matrix	64
7.1.2 Proportional-Integral-Derivative (PID)	64
7.2 Board and System Implementation of Intel® QST	66
7.3 Intel® QST Configuration and Tuning	68