Kyocera TASKalfa 4500i Kyocera Command Center RX User Guide Rev-1.2 - Page 26

Start > Information, Basic Basic > Defaults > Network

Get Kyocera TASKalfa 4500i PDF manuals and user guides View all Kyocera TASKalfa 4500i manuals
Add to My Manuals
Save this manual to your list of manuals

Page 26 highlights

Settings Pages This allows you to verify the accumulated number of printed pages for each paper size and color (Monochrome, Mono Color, and Full Color). A page printed on both sides is counted as two pages. Counters > Scanned Pages Provide information of the number of pages copied, faxed, and other (scanned), respectively. Start > Information This page provides information about user account. User Login This shows the number of registered users. For details, see Basic > Security > User Login on page 6-8. Basic Page This section includes settings that apply to the device, such as Device Defaults, Security, and basic Networking. Basic > Defaults > Network This page allows you to make the settings that are required for network printing and sending E-mail. For more information, refer to Advanced > Protocols > TCP/IP > General on page 6-29. You must restart this machine after you have completed these settings in order to properly register the content of those settings in the machine. Refer to Basic > Defaults > Reset on page 6-6. Host Name Specifies a name for the printing system network component. This name is used as the NetBEUI printer name and as the WSD device name. LAN Interface Specifies the communication rate from Auto, 10BASE-T-Half, 10BASE-TFull, 100BASE-TX-Half, 100BASE-TX-Full and 1000BASE-T. If you change the communication rate, you must restart the machine in order to make this setting valid. IPv4 Settings • DHCP/BOOTP Specifies whether or not to obtain an IP address using DHCP or BOOTP. • IP Address (IPv4) Assigns the Internet Protocol address on the printing system network component. Format of the IP address is four-byte (32-bit) numbers separated by dots, for example, 192.168.110.171. • Subnet Mask Specifies the subnet mask of the hosts or network with which the print system is connecting. If you have manually assigned an IP address that starts with a number between 192 and 223, it is recommended that you set the subnet mask to "255.255.255.0." • Default Gateway Specifies the IP address of the default gateway. IPv6 Settings 6-4 User Guide

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
Settings Pages
This allows you to verify the accumulated number of printed pages for each
paper size and color (Monochrome, Mono Color, and Full Color). A page
printed on both sides is counted as two pages.
Counters > Scanned Pages
Provide information of the number of pages copied, faxed, and other
(scanned), respectively.
Start > Information
This page provides information about user account.
User Login
This shows the number of registered users. For details, see
Basic > Security
> User Login
on page 6-8.
Basic Page
This section includes settings that apply to the device, such as Device Defaults,
Security, and basic Networking.
Basic > Defaults > Network
This page allows you to make the settings that are required for network printing
and sending E-mail. For more information, refer to
Advanced > Protocols >
TCP/IP > General
on page 6-29.
You must restart this machine after you have completed these settings in order
to properly register the content of those settings in the machine. Refer to
Basic
> Defaults > Reset
on page 6-6.
Host Name
Specifies a name for the printing system network component. This name is
used as the NetBEUI printer name and as the WSD device name.
LAN Interface
Specifies the communication rate from
Auto
,
10BASE-T-Half
,
10BASE-T-
Full
,
100BASE-TX-Half
,1
00BASE-TX-Full
and
1000BASE-T
. If you
change the communication rate, you must restart the machine in order to
make this setting valid.
IPv4 Settings
•
DHCP/BOOTP
Specifies whether or not to obtain an IP address using DHCP or BOOTP.
•
IP Address (IPv4)
Assigns the Internet Protocol address on the printing system network
component. Format of the IP address is four-byte (32-bit) numbers separated
by dots, for example, 192.168.110.171.
•
Subnet Mask
Specifies the subnet mask of the hosts or network with which the print system
is connecting. If you have manually assigned an IP address that starts with a
number between 192 and 223, it is recommended that you set the subnet
mask to "255.255.255.0."
•
Default Gateway
Specifies the IP address of the default gateway.
IPv6 Settings
User Guide
6-4