Kyocera TASKalfa 4500i Kyocera Command Center RX User Guide Rev-1.2 - Page 53

Advanced > Protocols > TCP/IP > IP Filters, RA Stateless, Default Gateway, DHCPv6 Stateful

Get Kyocera TASKalfa 4500i PDF manuals and user guides View all Kyocera TASKalfa 4500i manuals
Add to My Manuals
Save this manual to your list of manuals

Page 53 highlights

Settings Pages Specifies the IPv6 prefix length. It can be a decimal value between 0 and 128. • RA (Stateless) Select On to use RA instead of the DHCP server to configure IPv6 addresses. This function will require the presence of an RA Stateless router in the network that the device is connected to. • Default Gateway Specifies the IPv6 address of the default gateway. • DHCPv6 (Stateful) Specifies whether or not to obtain IPv6 IP addresses by automatic configuration. When RA is turned On, the IP addresses and server information are obtained via DHCPv6 based on the settings of the automatic configuration made under RA (router setting). This function requires the presence of a DHCPv6 router in the network that the device is connected to. • Domain Name Specifies the domain name of the domain to which the printing system belongs. • DNS Servers (Primary, Secondary) Specifies the IP addresses of the primary and secondary DNS (Domain Name System) servers. When DHCPv6 (Stateful) is turned On, you can select to use the DNS server obtained via DHCP, or you can enter static DNS server information in the Primary and Secondary fields provided. Advanced > Protocols > TCP/IP > IP Filters This page allows you to configure IP filters. IP filters restrict access to the printing system based on the IP addresses and protocols. Specify the IP addresses or network addresses of the hosts to which access is granted. If nothing is specified on this page, access from all hosts is allowed. IP Filter (IPv4) • IP Address (IPv4) Specifies the IP address or network address to be permitted. Subnet Mask Specifies the subnet mask to be permitted. When there are no entries, access is allowed to all. To allow access to a network, enter the network IPv4 address, and the subnet mask. For example: To allow access from all hosts on network 192, enter "192.0.0.0" for the IP address, and "255.0.0.0" for the subnet mask. Subnet mask can also be left blank. To allow access to a single IP address, enter the IPv4 address, and "255.255.255.255" for the subnet mask. • Protocols Specifies the protocol to be permitted. The following protocols can be selected: • LPD • FTP • IPP • ThinPrint COMMAND CENTER RX 6-31

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
Settings Pages
Specifies the IPv6 prefix length. It can be a decimal value between 0 and 128.
•
RA (Stateless)
Select
On
to use RA instead of the DHCP server to configure IPv6
addresses. This function will require the presence of an RA Stateless router
in the network that the device is connected to.
•
Default Gateway
Specifies the IPv6 address of the default gateway.
•
DHCPv6 (Stateful)
Specifies whether or not to obtain IPv6 IP addresses by automatic
configuration. When RA is turned
On
, the IP addresses and server
information are obtained via DHCPv6 based on the settings of the automatic
configuration made under RA (router setting). This function requires the
presence of a DHCPv6 router in the network that the device is connected to.
•
Domain Name
Specifies the domain name of the domain to which the printing system
belongs.
•
DNS Servers (Primary, Secondary)
Specifies the IP addresses of the primary and secondary DNS (Domain
Name System) servers. When DHCPv6 (Stateful) is turned
On
, you can
select to use the DNS server obtained via DHCP, or you can enter static DNS
server information in the Primary and Secondary fields provided.
Advanced > Protocols > TCP/IP > IP Filters
This page allows you to configure IP filters. IP filters restrict access to the
printing system based on the IP addresses and protocols.
Specify the IP addresses or network addresses of the hosts to which access is
granted.
If nothing is specified on this page, access from all hosts is allowed.
IP Filter (IPv4)
•
IP Address (IPv4)
Specifies the IP address or network address to be permitted.
Subnet Mask
Specifies the subnet mask to be permitted. When there are no entries,
access is allowed to all.
To allow access to a network, enter the network IPv4 address, and the
subnet mask. For example: To allow access from all hosts on network 192,
enter "192.0.0.0" for the IP address, and "255.0.0.0" for the subnet
mask. Subnet mask can also be left blank.
To allow access to a single IP address, enter the IPv4 address, and
"255.255.255.255" for the subnet mask.
•
Protocols
Specifies the protocol to be permitted. The following protocols can be
selected:
•
LPD
•
FTP
•
IPP
•
ThinPrint
COMMAND CENTER RX
6-31