Kyocera TASKalfa 4500i Kyocera Command Center RX User Guide Rev-1.2 - Page 57

Advanced > Protocols > NetBEUI, Advanced > E-mail > SMTP > General, SMTP Server Timeout

Get Kyocera TASKalfa 4500i PDF manuals and user guides View all Kyocera TASKalfa 4500i manuals
Add to My Manuals
Save this manual to your list of manuals

Page 57 highlights

Settings Pages Specifies the name of the printing system in the AppleTalk network. Zone Name Specifies the name of the AppleTalk zone (network). An asterisk (*) means the default zone. Advanced > Protocols > NetBEUI Peer-to-peer printing (SMB Print) is available using NetBEUI protocol. With this method, the printing system is located in Windows Network Neighborhood. NetBEUI is an enhanced version of the NetBIOS protocol, which is used for transport of SMB protocol. NetBEUI Protocol Enables or disables NetBEUI protocol. If NetBEUI is turned On, name resolution via NetBIOS (NMB) can be used. Printer Name Printer Name correlates with Host Name in the TCP/IP General page (Refer to Advanced > Protocols > TCP/IP > General on page 6-29). If you want to change the NetBEUI printer name, change the TCP/IP Host Name. Workgroup Workgroup represents the workgroup which will appear in Entire Network in "Windows Network Neighborhood." Comment You can enter comments here. (This can also be left blank.) Advanced > E-mail > SMTP > General Device event reports and counter status such as Low Toner and other information can be sent automatically via E-mail to the specified E-mail address. To use the mail function, configure SMTP (Simple Mail Transfer Protocol) to connect this device to an E-mail server. SMTP Enables or disables SMTP protocol. To use E-mail, this protocol must be enabled. SMTP Port Number Set the SMTP Port Number, or use the SMTP default port 25. Choose the default port number 465 for SMTP connections over SSL. SMTP Server Name Enter the SMTP server host name or its IP address. If entering the host name, rather than the IP address, a DNS server address must also be configured. The DNS server address may be entered on the TCP/IP General page (refer to Advanced > Protocols > TCP/IP > General on page 6-29). SMTP Server Timeout Sets the timeout in seconds during which this device tries to connect to the SMTP server. Authentication Protocol Enables or disables the SMTP authentication protocol or sets POP before SMTP as the authentication type. Authenticate as Specifies the user to be authenticated in SMTP authentication. When POP3 User 1 to 3 (Refer to Advanced > E-mail > POP3 > User # on page 6-38) and COMMAND CENTER RX 6-35

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
Settings Pages
Specifies the name of the printing system in the AppleTalk network.
Zone Name
Specifies the name of the AppleTalk zone (network). An asterisk (*) means
the default zone.
Advanced > Protocols > NetBEUI
Peer-to-peer printing (SMB Print) is available using NetBEUI protocol. With this
method, the printing system is located in Windows Network Neighborhood.
NetBEUI is an enhanced version of the NetBIOS protocol, which is used for
transport of SMB protocol.
NetBEUI Protocol
Enables or disables NetBEUI protocol. If NetBEUI is turned
On
, name
resolution via NetBIOS (NMB) can be used.
Printer Name
Printer Name correlates with Host Name in the
TCP/IP General
page (Refer
to
Advanced > Protocols > TCP/IP > General
on page 6-29). If you want to
change the NetBEUI printer name, change the TCP/IP Host Name.
Workgroup
Workgroup represents the workgroup which will appear in
Entire Network
in
"Windows Network Neighborhood."
Comment
You can enter comments here. (This can also be left blank.)
Advanced > E-mail > SMTP > General
Device event reports and counter status such as Low Toner and other
information can be sent automatically via E-mail to the specified E-mail address.
To use the mail function, configure SMTP (Simple Mail Transfer Protocol) to
connect this device to an E-mail server.
SMTP
Enables or disables SMTP protocol. To use E-mail, this protocol must be
enabled.
SMTP Port Number
Set the SMTP Port Number, or use the SMTP default port 25. Choose the
default port number 465 for SMTP connections over SSL.
SMTP Server Name
Enter the SMTP server host name or its IP address. If entering the host
name, rather than the IP address, a DNS server address must also be
configured. The DNS server address may be entered on the
TCP/IP General
page (refer to
Advanced > Protocols > TCP/IP > General
on page 6-29).
SMTP Server Timeout
Sets the timeout in seconds during which this device tries to connect to the
SMTP server.
Authentication Protocol
Enables or disables the SMTP authentication protocol or sets
POP before
SMTP
as the authentication type.
Authenticate as
Specifies the user to be authenticated in SMTP authentication. When POP3
User
1
to
3
(Refer to
Advanced > E-mail > POP3 > User #
on page 6-38) and
COMMAND CENTER RX
6-35